This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACED63X80, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPD Double Rod Compact Cylinder ACPD63X80
The AirTAC ACPD Double Rod Compact Cylinder ACPD63X80 is a double acting, double rod DIN-standard tight/compact air cylinder with a Ø63mm bore and 80mm stroke, 1/8" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACED63X80 (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ63 mm
- Stroke80 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM10×1.5
- StatusDiscontinued → ACED63X80
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPD Double Rod Compact Cylinder ACPD63X80
A double acting compact cylinder with a rod leaving both covers, the ACPD63X80 pushes and pulls with identical output because each stroke works on the rod-side area: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa in either direction. The 63 mm bore drives a 16 mm through-rod over an 80 mm stroke at 30-500 mm/s, with a fixed TPU bumper at each end to soften the stops. Its hard-anodized aluminium body keeps the mounting length roughly 50% shorter than an ISO 15552 profile cylinder, so it slots into tight gantries and fixture plates.
Because the rod passes through both covers, the back-end rod can carry a sensor flag or a second tool, and the symmetric mount resists rotation and side load. Note that this model is discontinued: the current-production direct is the ISO 21287 ACED63X80, so confirm the mounting dimensions before swapping.
Airtac ACPD Double Rod Compact Cylinder ACPD63X80 Technical Specifications
| Model | Airtac ACPD Double Rod Compact Cylinder ACPD63X80 |
|---|---|
| Series | ACPD DIN compact cylinder (discontinued) |
| Replacement | ACED63X80 |
| Bore size | Ø63 mm |
| Stroke | 80 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 250 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACED63X80 (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACPD Double Rod Compact Cylinder ACPD63X80
| ACPD | DIN compact cylinder (double-rod, discontinued). |
|---|---|
| 63 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPD Double Rod Compact Cylinder ACPD63X80 Is Used
Twin-sided weld fixture clamp
The through-rod clamps a steel bracket from both covers at once, delivering 1458.1 N per side at 0.5 MPa inside a fixture plate too short for a full-length profile cylinder.
Reciprocating pusher on a packaging line
Equal push and pull force drives a carton pusher back and forth at 30-500 mm/s, with the rear rod carrying a flag for a switch when the -S magnet is ordered.
Replacing the Airtac ACPD Double Rod Compact Cylinder ACPD63X80 with the ACED63X80
At 1458.1 N per side at 0.5 MPa, the 63 mm bore sits between the 50 mm (881.2 N) and 80 mm (2356.2 N) sizes; step down for lighter clamps or up for heavier presses. The through-rod gives equal force both ways, so it is a poor match for loads that must stay put when air is lost - add a rod lock or pilot check for held positions. Mount it on FA/FB flanges or LB feet, and if you need position sensing, order the -S code to enable CMSE / DMSE switches; this version has no magnet fitted. For new projects, specify the ACED63X80 instead.
Replacement checklist
- ✓ Current-production ACE → ACED63X80
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPD Double Rod Compact Cylinder ACPD63X80 FAQ
It is a double-rod cylinder, so output is identical both ways: 1458.1 N at 0.5 MPa, 2041.3 N at 0.7 MPa, and up to 297.4 kgf at 1.0 MPa. Both strokes use the rod-side area, so push never exceeds pull. Operating range is 0.15-1.0 MPa (22-145 psi) with 1.5 MPa (215 psi) proof pressure.
The hard-anodized aluminium body follows the short ISO 21287-class format, saving about 50% of the mounting length of an ISO 15552 profile cylinder, with FA/FB flange or LB foot mounting and a fixed TPU bumper at each end that only decelerates the stroke. The ACPD63X80 is discontinued; the current direct is the ACED63X80 in the same bore, stroke and force class - confirm the ISO 21287 mounting dimensions before swapping.
Request a Quote for the ACED63X80
Send us the quantity and destination. We confirm price, stock and lead time on the ACED63X80 replacement — usually within 7-8 hours.