This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACEJ16X110-100S, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPJ Adjustable Compact Cylinder ACPJ16X110-100S
The AirTAC ACPJ Adjustable Compact Cylinder ACPJ16X110-100S is a double acting, double rod, adjustable stroke DIN-standard tight/compact air cylinder with a Ø16mm bore and 110mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACEJ16X110-100S (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ16 mm
- Stroke110 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM4×0.7
- StatusDiscontinued → ACEJ16X110-100S
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPJ Adjustable Compact Cylinder ACPJ16X110-100S
This double acting compact cylinder trims its extend stroke on site: the -100 stop screw shortens the 110 mm stroke by up to 100 mm, giving a usable range of 10-110 mm. At 0.5 MPa the 16 mm bore pushes 100.5 N and pulls 75.4 N, rising to 140.7 N at 0.7 MPa. The 110 mm stroke is above the 75 mm standard limit for bore 16, so it is a made-to-order build. This model is discontinued; the current drop-in is ACEJ16X110, and buyers should confirm ISO 21287 mounting dimensions before swapping because the ACPJ follows the DIN standard.
The short ISO 21287-class body saves roughly 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight fixtures and guarding. Because the -S code was ordered, the magnet is fitted and CMSE / DMSE reed or solid-state switches can be mounted directly on the body. A practical sizing check: about 60 N of the push force is realistic working output at 0.5 MPa, which lifts roughly 5 kg vertically with a 2:1 margin. A fixed TPU bumper at each end decelerates the piston; it never locks or holds a load, so on air loss the rod will drift.
Airtac ACPJ Adjustable Compact Cylinder ACPJ16X110-100S Technical Specifications
| Model | Airtac ACPJ Adjustable Compact Cylinder ACPJ16X110-100S |
|---|---|
| Series | ACPJ DIN compact cylinder (discontinued) |
| Replacement | ACEJ16X110-100S |
| Bore size | Ø16 mm |
| Stroke | 110 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M4×0.7 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 75 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACEJ16X110-100S (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 75 N |
| 0.7 MPa | 106 N |
| Max (@1.0 MPa) | 15 kgf |
ACPJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac ACPJ Adjustable Compact Cylinder ACPJ16X110-100S
| ACPJ | DIN compact cylinder (adjustable-stroke, discontinued). |
|---|---|
| 16 | Bore size in mm. |
| ×110 | Stroke length in mm. |
| -100 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPJ Adjustable Compact Cylinder ACPJ16X110-100S Is Used
Fixture clamp with trimmed stroke
On a small CNC jig, the stop screw is set to 25 mm so the 8 mm rod clamps thin aluminum brackets with about 100.5 N at 0.5 MPa without over-compressing the part.
Position-verified ejector
With the -S magnet fitted, a DMSE solid-state switch confirms full retract on a PCB tray eject station, while the 10-110 mm adjustable range lets one cylinder serve several tray depths.
Compact carton push-off
In a tight packaging gantry where a full-length ISO 15552 cylinder will not fit, the short body pushes 150 g blister packs off a conveyor at 300 mm/s within the 30-500 mm/s band.
Replacing the Airtac ACPJ Adjustable Compact Cylinder ACPJ16X110-100S with the ACEJ16X110-100S
Size between bores: the 12 mm bore gives 56.5 N push at 0.5 MPa while the 20 mm bore reaches 157.1 N, so this 16 mm unit at 100.5 N sits mid-range for light clamping and indexing. Remember the stop screw is a mechanical end stop, not a mid-stroke lock. FA/FB flanges and LB feet bolt to the standard face, and the optional -S magnet (fitted here) pairs with CMSE / DMSE switches. For new projects specify the ACEJ16X110, the current-production successor.
Replacement checklist
- ✓ Current-production ACE → ACEJ16X110-100S
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPJ Adjustable Compact Cylinder ACPJ16X110-100S FAQ
At 0.5 MPa it pushes 100.5 N and pulls 75.4 N; at 0.7 MPa push is 140.7 N and pull 105.6 N; theoretical maximum is 20.5 kgf at 1.0 MPa. Plan on roughly 60 N of real working force at 0.5 MPa, which lifts about 5 kg vertically with a 2:1 margin. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof 1.5 MPa (215 psi), speed 30-500 mm/s.
The -100 code is a 100 mm adjustment window: an external stop screw shortens the extend stroke anywhere in the 10-110 mm range; it cannot lengthen the stroke past 110 mm and it is not a load-holding brake. The ACPJ family is discontinued. The current-production drop-in is ACEJ16X110 in the same bore, stroke and force class - confirm the ISO 21287 mounting dimensions before swapping, since the ACPJ was built to the DIN standard.
Related AirTAC ACE Cylinders
Request a Quote for the ACEJ16X110-100S
Send us the quantity and destination. We confirm price, stock and lead time on the ACEJ16X110-100S replacement — usually within 7-8 hours.