Airtac B06-SCD Battery-Specific Standard Cylinder B06-SCD100X25S
The AirTAC Airtac B06-SCD Battery-Specific Standard Cylinder B06-SCD100X25S is a genuine double-acting DOUBLE-ROD air cylinder: the Ø25mm piston rod extends from BOTH end caps, giving equal effective area — and therefore equal force — in push and pull. Ø100mm bore, 25mm stroke, PT1/2 ports and adjustable end cushioning.
- BoreØ100 mm
- Rod (both ends)Ø25 mm
- Stroke25 mm
- Port sizePT1/2
- Rod configDouble rod (through)
- CushionAdjustable, 29 mm
About the Airtac B06-SCD Battery-Specific Standard Cylinder B06-SCD100X25S
The B06-SCD100X25S is an AirTAC double-acting, double-rod cylinder where the B06- prefix designates it as a battery-manufacturing dedicated variant of the standard SCD100X25S. Mechanically, it shares the exact same physical specifications, offering identical thrust in both directions thanks to the through-rod design which subtracts the rod area from both chambers.
With a 100 mm bore, it generates 3681 N of force each way at 0.5 MPa and reaches 6626 N at its 0.9 MPa maximum operating pressure. The Ø25 mm piston rod extends from both ends, providing anti-rotation stability and dual tooling mounting points. This short 25 mm stroke is ideal for high-force clamping or pressing tasks in cell assembly lines, and the built-in magnet allows CMSG or DMSG sensors to track position along the 29 mm cushioned barrel.
Airtac B06-SCD Battery-Specific Standard Cylinder B06-SCD100X25S Technical Specifications
| Model | Airtac B06-SCD Battery-Specific Standard Cylinder B06-SCD100X25S |
|---|---|
| Series | SCD double-rod tie-rod cylinder |
| Bore size | Ø100 mm |
| Rod diameter | Ø25 mm (both ends) |
| Stroke | 25 mm |
| Rod configuration | Double rod — rod through both caps |
| Acting type | Double acting |
| Port size | PT1/2 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SCD (double-rod) datasheet. Because the rod runs through both caps, the effective area is (bore² − rod²) in both directions. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø100mm, double rod)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3682 N | 3682 N |
| 0.7 MPa | 5154 N | 5154 N |
| Max (@1.0 MPa) | 751 kgf | |
Push and pull are EQUAL on a double-rod cylinder — both chambers lose the rod area, so effective area = (bore² − rod²) each way. Actual usable force is lower than theoretical due to friction and back-pressure; size with a safety margin.
Model Code: Airtac B06-SCD Battery-Specific Standard Cylinder B06-SCD100X25S
| SCD | Double-rod tie-rod cylinder series (rod out both ends). |
|---|---|
| 100 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related types: SC (single rod), SCJ (adjustable stroke), SCT (multi-position). SCD mounting: Basic, FA, LB, TC, TCM1. Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac B06-SCD Battery-Specific Standard Cylinder B06-SCD100X25S Is Used
Battery Cell Stacking
Provides equal 3681 N push and pull force for pressing and aligning battery cells during module stacking, utilizing the dual rods to maintain parallel contact surfaces.
Tab Welding Clamp
The short 25 mm stroke delivers rapid, high-force clamping for battery tab welding, while the built-in magnet confirms clamp position for the weld controller.
Shuttle Transfer
Uses the rear protruding rod to actuate a secondary mechanism or sensor flag simultaneously, synchronizing two actions in a pack assembly conveyor setup.
Is the Airtac B06-SCD Battery-Specific Standard Cylinder B06-SCD100X25S the Right Cylinder?
Select this 100 mm bore double-rod cylinder when your battery handling fixture requires symmetric force and a rear rod for mounting secondary tooling or a stopper flag. If your application requires less force, stepping down to the 80 mm bore yields 2268 N at 0.5 MPa. For applications needing true non-rotating precision under heavy side loads, a dedicated guided cylinder is superior to relying solely on the through-rod guidance.
Because this is a short 25 mm stroke, rod bending is negligible, but always ensure the load is axially aligned to maximize bearing life. When replacing this unit, you must match five points: the 100 mm bore, 25 mm stroke, PT port thread, basic mounting, and the -S magnet option. Note that the adjustable air cushions only decelerate the piston near stroke end; they do not lock or hold the load if air pressure is lost.
Double-rod checklist
- ✓ Need equal force / speed both directions?
- ✓ Rear rod for tooling, stopper or sensor flag?
- ✓ Better rod guidance / anti-rotation?
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Keep BOTH rod ends clear of side load and interference.
- check Adjust end cushion screws for smooth stops.
- check Use SCD mounting accessory (FA / LB / TC / TCM1).
- check Installation by qualified personnel per AirTAC docs.
Airtac B06-SCD Battery-Specific Standard Cylinder B06-SCD100X25S FAQ
The B06- prefix indicates this is a battery-manufacturing dedicated cylinder. It is mechanically identical to the standard AirTAC SCD100X25S, meaning the bore, stroke, 3681 N force, and port sizes are exactly the same.
The double-rod design ensures push and pull forces are identical at 3681 N (0.5 MPa) because the rod area is subtracted from both sides. It also provides better rod guidance, anti-rotation resistance, and a rear rod for mounting a sensor flag or secondary tooling.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SCD Double-Rod Cylinders
Request a Quote for Airtac B06-SCD Battery-Specific Standard Cylinder B06-SCD100X25S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.