Airtac B06-SCD Battery-Specific Standard Cylinder B06-SCD80X75
The AirTAC Airtac B06-SCD Battery-Specific Standard Cylinder B06-SCD80X75 is a genuine double-acting DOUBLE-ROD air cylinder: the Ø25mm piston rod extends from BOTH end caps, giving equal effective area — and therefore equal force — in push and pull. Ø80mm bore, 75mm stroke, PT3/8 ports and adjustable end cushioning.
- BoreØ80 mm
- Rod (both ends)Ø25 mm
- Stroke75 mm
- Port sizePT3/8
- Rod configDouble rod (through)
- CushionAdjustable, 28 mm
About the Airtac B06-SCD Battery-Specific Standard Cylinder B06-SCD80X75
The B06-SCD80X75 is an AirTAC double-acting, double-rod cylinder where the B06- prefix designates it as a battery-manufacturing dedicated variant, mechanically identical to the standard SCD80X75. Because the Ø25 mm piston rod passes through both end caps, the effective area is identical in both chambers, yielding an equal push and pull force of 2268 N at 0.5 MPa and 4082 N at 0.9 MPa.
With a 75 mm stroke, this compact unit is built for rapid, short-travel transfer tasks on cell and module assembly lines. The through-rod design provides superior anti-rotation characteristics and symmetric bearing loading compared to a single-rod cylinder. It features adjustable cushions with a 28 mm length on both ends to smoothly decelerate the payload, and the body length A(SCD) is 257 mm.
Airtac B06-SCD Battery-Specific Standard Cylinder B06-SCD80X75 Technical Specifications
| Model | Airtac B06-SCD Battery-Specific Standard Cylinder B06-SCD80X75 |
|---|---|
| Series | SCD double-rod tie-rod cylinder |
| Bore size | Ø80 mm |
| Rod diameter | Ø25 mm (both ends) |
| Stroke | 75 mm |
| Rod configuration | Double rod — rod through both caps |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 28 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SCD (double-rod) datasheet. Because the rod runs through both caps, the effective area is (bore² − rod²) in both directions. Confirm against the product label before installation. Thread options: PT (standard) / G.
Theoretical Output Force (Ø80mm, double rod)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2268 N | 2268 N |
| 0.7 MPa | 3175 N | 3175 N |
| Max (@1.0 MPa) | 463 kgf | |
Push and pull are EQUAL on a double-rod cylinder — both chambers lose the rod area, so effective area = (bore² − rod²) each way. Actual usable force is lower than theoretical due to friction and back-pressure; size with a safety margin.
Model Code: Airtac B06-SCD Battery-Specific Standard Cylinder B06-SCD80X75
| SCD | Double-rod tie-rod cylinder series (rod out both ends). |
|---|---|
| 80 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related types: SC (single rod), SCJ (adjustable stroke), SCT (multi-position). SCD mounting: Basic, FA, LB, TC, TCM1. Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
Where the Airtac B06-SCD Battery-Specific Standard Cylinder B06-SCD80X75 Is Used
Battery Cell Stacking
Provides equal push and pull force for stacking prismatic cells, ensuring precise alignment without rotational drift during the compression and release cycle.
Module Shuttle Transfer
The through-rod allows mounting a secondary stopper or sensor flag on the rear side, enabling compact bidirectional shuttle transfers on tight pack assembly conveyors.
Tab Welding Clamp
Delivers 2268 N of clamping force at 0.5 MPa on both extension and retraction to hold battery tabs firmly during ultrasonic welding operations.
Is the Airtac B06-SCD Battery-Specific Standard Cylinder B06-SCD80X75 the Right Cylinder?
Select this 80 mm bore when your battery handling fixture requires substantial equal force in both directions, such as 2268 N at 0.5 MPa. If your tabbing or stacking mechanism needs less thrust, consider stepping down to the 63 mm bore which provides 1402 N. If you only need unidirectional thrust and want to save space, the single-rod SC80X75 is a better fit, while heavy side-loading demands a true guided cylinder rather than relying on the through-rod alone.
When ordering a replacement, verify a 5-point match: 80 mm bore, 75 mm stroke, PT3/8 port thread, basic mounting (or the correct SCD accessory like F-SC80LB), and the presence or absence of a magnetic piston (-S). Note that the adjustable air cushion only decelerates the piston near stroke end; it does not lock or hold the load. If your battery cell fixture must maintain position without live air pressure, you must integrate an external mechanical lock or pilot-operated check valve.
Double-rod checklist
- ✓ Need equal force / speed both directions?
- ✓ Rear rod for tooling, stopper or sensor flag?
- ✓ Better rod guidance / anti-rotation?
- ✓ Port/thread type (PT/NPT/G)
- ✓ Magnet (-S) for sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Keep BOTH rod ends clear of side load and interference.
- check Adjust end cushion screws for smooth stops.
- check Use SCD mounting accessory (FA / LB / TC / TCM1).
- check Installation by qualified personnel per AirTAC docs.
Airtac B06-SCD Battery-Specific Standard Cylinder B06-SCD80X75 FAQ
The B06- prefix indicates this is an AirTAC battery-manufacturing dedicated cylinder. It is mechanically identical to the standard SCD80X75 double-rod cylinder, offering the same 80 mm bore, 75 mm stroke, and 2268 N equal push/pull force at 0.5 MPa, but is designated for battery cell, module, and pack assembly lines.
A double-rod cylinder provides identical thrust in both directions (2268 N at 0.5 MPa here) because the rod area is subtracted from both chambers. The through-rod offers better anti-rotation stability, symmetric bearing wear, and allows you to mount tooling or a sensor flag on the rear side, which is highly beneficial for compact battery handling fixtures.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SCD Double-Rod Cylinders
Request a Quote for Airtac B06-SCD Battery-Specific Standard Cylinder B06-SCD80X75
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.