Airtac B06-TCM Battery-Specific Cylinder B06-TCM25X100S
The AirTAC B06-TCM Battery-Specific Cylinder B06-TCM25X100S is a genuine JIS-standard guided cylinder with a Ø25mm bore and 100mm stroke on twin guide rods. Its integrated brass sliding bearing gives high radial-load and impact resistance — about double the horizontal impact tolerance of a plain cylinder, holding the tool square to ±0.08° of rotation without any external linear guide.
- BoreØ25 mm
- Stroke100 mm
- Port size1/8"
- BearingBrass sliding bearing
- Non-rotating±0.08°
- CushionRubber bumper
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac B06-TCM Battery-Specific Cylinder B06-TCM25X100S
The B06-TCM25X100S is an AirTAC JIS guided twin-rod cylinder built for battery-manufacturing lines. The B06- prefix marks this as a battery-dedicated variant of the base TCM25X100S, meaning it is mechanically identical to the standard unit. It uses a double-acting drive piston running between two guide rods in a single integrated body, eliminating the need for an external linear slide. A brass sliding bearing supports the rods, offering about twice the horizontal impact resistance of a plain cylinder while shrugging off dust, grit, and debris where a steel-ball guide would jam.
Delivering 245 N of push and 189 N of pull at 0.5 MPa, this Ø25 bore unit is suited for cell stacking or module handling. It holds a non-rotating tolerance of ±0.08°, keeping a gripper or plate square under off-centre loads. The Ø12 piston rod uses 1/8" ports, and two independent upper and side port groups let you plumb from whichever face is clear. Stroke ends are damped by fixed elastomer pads rather than an adjustable cushion, and the standard built-in magnet works with CS1 reed or DS1 electronic switches in the four sensor slots.
Airtac B06-TCM Battery-Specific Cylinder B06-TCM25X100S Technical Specifications
| Model | Airtac B06-TCM Battery-Specific Cylinder B06-TCM25X100S |
|---|---|
| Series | TCM JIS guided (twin-rod) cylinder |
| Bore size | Ø25 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Bearing | Brass sliding bearing |
| Port size | 1/8" |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Non-rotating tolerance | ±0.08° (retracted) |
| Cushion | Rubber bumper |
| Max std stroke | Up to 250 mm |
Specifications follow the official AirTAC TCL/TCM series datasheet (JIS standard). Confirm against the product label before installation. Thread options: PT (blank) / G / NPT. Every TC model ships with a built-in magnet for sensor switches.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 189 N |
| 0.7 MPa | 344 N | — |
| Max | 50 kgf | |
Force is set by the bore and piston rod (Ø12 mm); the twin guide rods carry side load and torque, not thrust. Actual usable force is lower than theoretical due to friction and back-pressure.
Model Code: Airtac B06-TCM Battery-Specific Cylinder B06-TCM25X100S
| TC | Tri-rod (guided, twin-rod) cylinder, double acting. |
|---|---|
| M | Bearing: Brass sliding bearing (M = brass sliding). |
| 25 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| S | Built-in magnet (standard on TC) for a magnetic sensor switch. |
Sister type: TCL25X100 (steel-ball linear bearing, lower friction & higher precision). Thread codes: blank = PT · G · T = NPT.
Where the Airtac B06-TCM Battery-Specific Cylinder B06-TCM25X100S Is Used
Battery Cell Stacking Press
Pushes lithium cells into alignment during stacking with 245 N of force at 0.5 MPa. The brass sliding bearing tolerates abrasive dust from electrode cutting, maintaining a ±0.08° non-rotating accuracy so the cell faces remain perfectly parallel.
Module Transfer Gate
Stops and positions heavy battery modules on a conveyor. The twin guide rods absorb the radial side load of the moving pallet, while the impact-tolerant brass bearing survives hard knocks without failing like a steel-ball guide.
Tab Welding Clamp
Holds battery tabs flat for laser welding. The integrated guide keeps the clamping face square under off-centre pressure, and the 1/8" ported Ø12 rod cycles at 30-500 mm/s to maintain high throughput on the weld line.
Is the Airtac B06-TCM Battery-Specific Cylinder B06-TCM25X100S the Right Cylinder?
This 25 mm bore generates roughly 245 N of thrust at 0.5 MPa. If you need less force, stepping down to the Ø20 bore yields about 157 N of push, while moving up to the Ø32 bore provides 402 N for heavier pack manipulation. Because the guide resists rotation but not gravity, the rod will drift if air pressure is lost; add an external rod lock or pilot check valve for fail-safe load holding. Choose the TCL series instead if your task demands the low-friction, high-precision motion of a steel-ball linear bearing for vertical high-load work.
To replace this unit, match the 25 mm bore, 100 mm stroke, 1/8" port, PT thread form, and the standard S magnet. The 100 mm stroke is well within the 250 mm maximum standard limit for this bore, so it is a stock configuration. Precision locating holes allow you to remove and re-fit the cylinder without re-teaching the position.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Side load / torque the guide must carry
- ✓ TCL (precision, low friction) vs TCM (impact, radial load)
- ✓ Stroke & mounting face (top / bottom / rear)
- ✓ Port/thread type (PT/NPT/G)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check The guide unit takes side load & torque — but do not exceed the max safe load/torque for your stroke.
- check Mount from the top, bottom (screw or T-slot) or rear face; use the precision locating holes.
- check Do not disassemble the fixing block or guide unit — factory-set precision.
- check Fit CS1 / DS1 magnetic switches in the four sensor slots as needed.
Airtac B06-TCM Battery-Specific Cylinder B06-TCM25X100S FAQ
At 0.5 MPa this double-acting cylinder provides 245 N of push and 189 N of pull. At the maximum operating pressure of 0.7 MPa, the push force increases to 344 N. The theoretical maximum force is 50 kgf.
The B06- prefix indicates this is an AirTAC battery-manufacturing dedicated variant of the TCM25X100S; mechanically, every spec matches the base model exactly. Each end lands on a fixed TPU bumper to soften the stop, but there is no adjustable air cushion screw to set.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC TCM Cylinders
Request a Quote for Airtac B06-TCM Battery-Specific Cylinder B06-TCM25X100S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.