Airtac B06-TCM Battery-Specific Cylinder B06-TCM25X75S
The AirTAC B06-TCM Battery-Specific Cylinder B06-TCM25X75S is a genuine JIS-standard guided cylinder with a Ø25mm bore and 75mm stroke on twin guide rods. Its integrated brass sliding bearing gives high radial-load and impact resistance — about double the horizontal impact tolerance of a plain cylinder, holding the tool square to ±0.08° of rotation without any external linear guide.
- BoreØ25 mm
- Stroke75 mm
- Port size1/8"
- BearingBrass sliding bearing
- Non-rotating±0.08°
- CushionRubber bumper
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac B06-TCM Battery-Specific Cylinder B06-TCM25X75S
The AirTAC B06-TCM25X75S is a JIS-standard twin-rod guided cylinder built for battery manufacturing lines, mechanically identical to the base TCM25X75S. The B06- prefix simply marks this as a battery-industry dedicated variant. A drive piston runs between two guide rods in a single integrated body, meaning no external linear rail is required. It delivers 245 N of push at 0.5 MPa, supported by a brass sliding bearing that shrugs off grit, debris, and hard knocks where a steel-ball guide would jam.
This 25 mm bore unit uses a Ø12 mm piston rod and 1/8" ports. Its twin-guide design holds a non-rotating tolerance of ±0.08°, keeping a gripper or tooling plate perfectly square under offset loads. Stroke ends are damped by fixed elastomer pads rather than an adjustable cushion. The standard built-in magnet works with CS1 reed or DS1 electronic switches in the four sensor slots.
Airtac B06-TCM Battery-Specific Cylinder B06-TCM25X75S Technical Specifications
| Model | Airtac B06-TCM Battery-Specific Cylinder B06-TCM25X75S |
|---|---|
| Series | TCM JIS guided (twin-rod) cylinder |
| Bore size | Ø25 mm |
| Stroke | 75 mm |
| Acting type | Double acting |
| Bearing | Brass sliding bearing |
| Port size | 1/8" |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Non-rotating tolerance | ±0.08° (retracted) |
| Cushion | Rubber bumper |
| Max std stroke | Up to 250 mm |
Specifications follow the official AirTAC TCL/TCM series datasheet (JIS standard). Confirm against the product label before installation. Thread options: PT (blank) / G / NPT. Every TC model ships with a built-in magnet for sensor switches.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 189 N |
| 0.7 MPa | 344 N | — |
| Max | 50 kgf | |
Force is set by the bore and piston rod (Ø12 mm); the twin guide rods carry side load and torque, not thrust. Actual usable force is lower than theoretical due to friction and back-pressure.
Model Code: Airtac B06-TCM Battery-Specific Cylinder B06-TCM25X75S
| TC | Tri-rod (guided, twin-rod) cylinder, double acting. |
|---|---|
| M | Bearing: Brass sliding bearing (M = brass sliding). |
| 25 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Built-in magnet (standard on TC) for a magnetic sensor switch. |
Sister type: TCL25X75 (steel-ball linear bearing, lower friction & higher precision). Thread codes: blank = PT · G · T = NPT.
Where the Airtac B06-TCM Battery-Specific Cylinder B06-TCM25X75S Is Used
Cell Stacking Press
Pushes prismatic cells into alignment during stacking with 245 N of force, where the brass sliding bearing tolerates electrode dust and mechanical impacts better than a ball guide.
Module Transfer Gate
Stops and positions heavy battery modules on a conveyor; the ±0.08° anti-rotation tolerance keeps the stopping blade square against shifting pallets.
Tab Welding Clamp
Holds battery tabs flat for laser welding, using the twin guide rods to absorb side loads from the welding head without needing a separate linear slide.
Is the Airtac B06-TCM Battery-Specific Cylinder B06-TCM25X75S the Right Cylinder?
This 25 mm bore generates 245 N of thrust at 0.5 MPa. If you need less force, step down to the Ø20 bore which provides roughly 157 N; for heavier duty, the Ø32 bore offers 402 N. Choose the sister TCL series with its steel-ball linear bearing instead if your task demands low friction or high vertical precision. To replace this unit, match the 25 mm bore, 75 mm stroke, 1/8" port, PT thread, and standard magnet (S).
Note that the guide prevents rotation but cannot fight gravity. If air pressure drops, the rod will drift, so fit an external rod lock or pilot check valve for fail-safe load holding.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Side load / torque the guide must carry
- ✓ TCL (precision, low friction) vs TCM (impact, radial load)
- ✓ Stroke & mounting face (top / bottom / rear)
- ✓ Port/thread type (PT/NPT/G)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check The guide unit takes side load & torque — but do not exceed the max safe load/torque for your stroke.
- check Mount from the top, bottom (screw or T-slot) or rear face; use the precision locating holes.
- check Do not disassemble the fixing block or guide unit — factory-set precision.
- check Fit CS1 / DS1 magnetic switches in the four sensor slots as needed.
Airtac B06-TCM Battery-Specific Cylinder B06-TCM25X75S FAQ
At 0.5 MPa it provides 245 N of push and 189 N of pull. At 0.7 MPa the push increases to 344 N, with a theoretical maximum force of 50 kgf. Operating pressure is 0.15-1.0 MPa and speed ranges from 30-500 mm/s.
The B06- prefix denotes this as a battery-manufacturing dedicated variant of the TCM25X75S; the physical specs are identical. It uses fixed rubber TPU bumpers at each end to soften the stop, meaning there is no adjustable air cushion screw to set.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC TCM Cylinders
Request a Quote for Airtac B06-TCM Battery-Specific Cylinder B06-TCM25X75S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.