Airtac B06-TCM Battery-Specific Cylinder B06-TCM32X75S
The AirTAC B06-TCM Battery-Specific Cylinder B06-TCM32X75S is a genuine JIS-standard guided cylinder with a Ø32mm bore and 75mm stroke on twin guide rods. Its integrated brass sliding bearing gives high radial-load and impact resistance — about double the horizontal impact tolerance of a plain cylinder, holding the tool square to ±0.06° of rotation without any external linear guide.
- BoreØ32 mm
- Stroke75 mm
- Port size1/8"
- BearingBrass sliding bearing
- Non-rotating±0.06°
- CushionRubber bumper
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac B06-TCM Battery-Specific Cylinder B06-TCM32X75S
The AirTAC B06-TCM32X75S is a JIS guided twin-rod double-acting cylinder featuring a brass sliding bearing. The "B06-" prefix designates this as a battery-manufacturing dedicated variant, mechanically identical to the standard TCM32X75S, built for cell stacking and module handling. It uses a drive piston running between two guide rods in a single integrated body, eliminating the need for an external linear guide. Delivering 402 N of push at 0.5 MPa, it handles substantial radial loads on the production line.
This 32 mm bore unit features a Ø16 mm piston rod and 1/8" ports, operating at speeds from 30-500 mm/s. The brass sliding bearing shrugs off dust and hard impacts, offering roughly double the horizontal impact resistance of a plain cylinder where a steel-ball guide might jam. With a non-rotating tolerance of ±0.06°, it keeps grippers square during off-centre tabbing tasks. Stroke ends are damped by fixed elastomer pads rather than an adjustable cushion.
Airtac B06-TCM Battery-Specific Cylinder B06-TCM32X75S Technical Specifications
| Model | Airtac B06-TCM Battery-Specific Cylinder B06-TCM32X75S |
|---|---|
| Series | TCM JIS guided (twin-rod) cylinder |
| Bore size | Ø32 mm |
| Stroke | 75 mm |
| Acting type | Double acting |
| Bearing | Brass sliding bearing |
| Port size | 1/8" |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Non-rotating tolerance | ±0.06° (retracted) |
| Cushion | Rubber bumper |
| Max std stroke | Up to 250 mm |
Specifications follow the official AirTAC TCL/TCM series datasheet (JIS standard). Confirm against the product label before installation. Thread options: PT (blank) / G / NPT. Every TC model ships with a built-in magnet for sensor switches.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 302 N |
| 0.7 MPa | 563 N | — |
| Max | 82 kgf | |
Force is set by the bore and piston rod (Ø16 mm); the twin guide rods carry side load and torque, not thrust. Actual usable force is lower than theoretical due to friction and back-pressure.
Model Code: Airtac B06-TCM Battery-Specific Cylinder B06-TCM32X75S
| TC | Tri-rod (guided, twin-rod) cylinder, double acting. |
|---|---|
| M | Bearing: Brass sliding bearing (M = brass sliding). |
| 32 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Built-in magnet (standard on TC) for a magnetic sensor switch. |
Sister type: TCL32X75 (steel-ball linear bearing, lower friction & higher precision). Thread codes: blank = PT · G · T = NPT.
Where the Airtac B06-TCM Battery-Specific Cylinder B06-TCM32X75S Is Used
Battery Cell Stacking Press
Pushes lithium pouch cells into stacking trays with 402 N of force at 0.5 MPa. The brass sliding bearing tolerates abrasive separator dust and grit without jamming.
Module Tab Alignment
Holds busbars flat for laser welding with a ±0.06° non-rotating tolerance. The twin guide rods absorb off-centre loads from mismatched cell heights.
Pack Transfer Stopper
Acts as a heavy gate on the conveyor line. The impact-resistant brass bearing withstands repeated hard knocks from moving battery packs without wearing out.
Is the Airtac B06-TCM Battery-Specific Cylinder B06-TCM32X75S the Right Cylinder?
When sizing this model, consider the neighbouring bores: stepping down to Ø25 yields about 245 N of push at 0.5 MPa, while moving up to Ø40 provides 628 N. Choose the sibling TCL series with its steel-ball linear bearing instead if your battery line requires low-friction, high-precision vertical positioning. Remember that air pressure loss will cause the rod to drift downward, as the guide resists rotation, not gravity; install an external rod lock for fail-safe holding. Replacement requires a 32 mm bore, 75 mm stroke, 1/8" PT ports, and the standard built-in magnet (S).
Quick checklist
- ✓ Required force at your working pressure
- ✓ Side load / torque the guide must carry
- ✓ TCL (precision, low friction) vs TCM (impact, radial load)
- ✓ Stroke & mounting face (top / bottom / rear)
- ✓ Port/thread type (PT/NPT/G)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check The guide unit takes side load & torque — but do not exceed the max safe load/torque for your stroke.
- check Mount from the top, bottom (screw or T-slot) or rear face; use the precision locating holes.
- check Do not disassemble the fixing block or guide unit — factory-set precision.
- check Fit CS1 / DS1 magnetic switches in the four sensor slots as needed.
Airtac B06-TCM Battery-Specific Cylinder B06-TCM32X75S FAQ
This 32 mm bore cylinder generates a push force of 402 N and a pull force of 302 N at 0.5 MPa. At 0.7 MPa, the push increases to 563 N. The theoretical maximum force is 82 kgf.
The B06- prefix marks this as a battery-manufacturing dedicated variant of the TCM32X75S, with identical mechanical specs. It uses a fixed rubber (TPU) bumper at each end to soften stops; it does not feature an adjustable air cushion.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC TCM Cylinders
Request a Quote for Airtac B06-TCM Battery-Specific Cylinder B06-TCM32X75S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.