The AirTAC GAR Air Regulators GAR10006LT is a genuine compact pressure regulator in a 59 g body. It sets and holds a steady downstream pressure across the 0.15 - 0.4 MPa range, with a 1/8" port and a built-in circular gauge. It regulates pressure only — it does not filter the air.
The AirTAC GAR10006LT is a compact air pressure regulator that sets and holds a steady downstream pressure from a varying supply. It is a regulator only: it does not clean the air or remove water or particles, so pair it with a GAFR100 filter-regulator or a GAF100 filter upstream when the line needs clean air. This lower-pressure L type regulates 0.15-0.4 MPa (20-58 psi), and the 1/8" NPT port with a 59 g body suits small tools and branch lines.
A pressed-in self-locking knob stops the setting from drifting under vibration or knocks, and the balanced adjustment mechanism holds the setpoint as supply pressure changes. The fitted circular gauge uses a clip and magnifier for space-saving, easy reading, and its scale reads psi/bar to match the NPT thread. Operating temperature is -5 to 70 C, and the unit must not freeze.
| Model | Airtac GAR Air Regulators GAR10006LT |
|---|---|
| Series | GAR100 air regulator |
| Port size | 1/8" (NPT thread) |
| Regulation type | Lower pressure |
| Pressure range | 0.15 - 0.4 MPa (20 - 58 psi) |
| Pressure gauge | Circular, psi / bar scale |
| Bracket | Included |
| Fluid | Air |
|---|---|
| Max. pressure | 1.0 MPa (145 psi) |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Adjustment | Self-locking press-in knob |
| Weight | 59 g |
Specifications follow the official AirTAC GAR catalogue (GAR100 page). The GAR100 has no reflux (K) option. This is a regulator only — it sets and holds a downstream pressure but does not filter the air. To clean the air as well, use the matching GAFR100 filter-regulator or add a GAF filter upstream.
| GAR100 | GA100 series air regulator — the compact single-body size. |
|---|---|
| 06 | Port size 1/8". This body offers M5 and 06 = 1/8". |
| L | Lower pressure regulation: 0.15 - 0.4 MPa (20 - 58 psi). GAR100 offers S or L. |
| (blank) | Mounting bracket included. |
| (blank) | Circular pressure gauge fitted. |
| T | NPT thread; gauge scale psi / bar. |
A GAR regulates pressure but does not filter. Need to clean the air too? The matching GAFR10006 is the same regulator with a built-in filter.
The GAR100 is the smallest body, for a small tool or branch line. For a bigger port and higher air demand, step up to the GAR200-600 range.
| This model | GAR100 · 1/8" · 59 g |
|---|---|
| One size up | GAR200 (170 g) |
| Add filtration | GAFR10006 (filter + regulator) |
Drops a small air screwdriver or nibbler to a gentle 0.15-0.4 MPa (20-58 psi) setting so delicate fastening work is not overdriven by supply swings.
Sets a repeatable low clamping pressure on a single benchtop jig cylinder, with the self-locking knob holding the value between shifts.
Trims one 1/8" NPT branch of a shop air system to its own lower pressure, read at a glance on the psi/bar gauge.
Choose GAR10006LT when a 1/8" NPT branch or bench tool needs a low, steady working pressure: the L type regulates 0.15-0.4 MPa (20-58 psi) with finer resolution in that low band than the standard S type. A circular gauge is fitted and reads psi/bar to match the NPT thread, and the mounting bracket is included for panel or line mounting. The 59 g body keeps installation easy in tight spots, but remember this is a regulator only; add a GAFR100 or a GAF100 upstream if the air also needs cleaning, and step up to GAR200 for heavier air demand. Because the standard S type covers a 0.85 MPa band against this L type's 0.25 MPa band, the S range is about 3.4x wider.
Quick checklist
This is a regulator only — it sets and holds pressure but does not filter or lubricate. Add a GAF filter or step up to the GAFR10006 filter-regulator as your air-prep needs grow.
It is an AirTAC GAR100 regulator with a 1/8" NPT port. The lower-pressure L type regulates 0.15-0.4 MPa (20-58 psi). Maximum supply pressure is 1.0 MPa (145 psi) and proof pressure is 1.5 MPa (215 psi); neither is a setpoint. Operating temperature is -5 to 70 C and the unit must not freeze. The body weighs 59 g and a circular gauge with a psi/bar scale is fitted.
The T in the code sets an NPT connecting thread, and on the GAR100 the thread also sets the fitted gauge scale: NPT models read psi/bar, PT models MPa/psi, and G models bar/MPa. So this GAR10006LT gives you inch-based tapered connections and a gauge whose primary scale is psi.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity, thread type (PT / G / NPT) and destination. We confirm price, stock and lead time — usually within 7-8 hours.