Airtac GC FRL Unit GC200C06MF1K
The AirTAC GC FRL Unit GC200C06MF1K is a genuine G-series three-unit F.R.L. combination: a separate filter, a separate regulator and a separate lubricator assembled as one air-preparation station. It has See datasheet ports, a 40 µm element, a differential-pressure drain and regulates 0.15 - 0.9 MPa (20 - 130 psi).
- TypeF.R.L. combination (3 units)
- Port sizeSee datasheet
- Regulating range0.15 - 0.9 MPa (20 - 130 psi)
- Filtering grade40 µm
- DrainDifferential-pressure drain
- Bowl materialPC
- Pressure gaugeFitted
- ThreadPT
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac GC FRL Unit GC200C06MF1K
The GC200 series is AirTAC's three-piece F.R.L. combination: separate filter, regulator and lubricator assembled as one set. This GC200C06MF1K configuration adds a reverse (check) valve, and otherwise carries a PT1/8 port, a manual-drain filter bowl, standard 40 um filtration and an embedded square gauge on an MPa scale. The check valve holds the downstream side if upstream supply is lost, while the set filters water and particulate, holds your set pressure and meters oil mist to the air line.
This is a genuine AirTAC part. The G-series combination is available in 200, 300, 400 and 600 sizes with ports up to 1 inch, PT / G(BSPP) / NPT threads, differential-pressure, automatic or manual drains, 40 um or 5 um (W) filter grades and gauge options. Max working pressure is 1.0 MPa (145 psi); operating range -5 to 70 C, non-freezing. Because flow is published as curves rather than one rated number, we confirm the datasheet figures for your application on request.
Airtac GC FRL Unit GC200C06MF1K Technical Specifications
| Model | Airtac GC FRL Unit GC200C06MF1K |
|---|---|
| Series | GC200 F.R.L. combination |
| Composition | Filter + regulator + lubricator (3 units) |
| Port size | See datasheet (PT thread) |
| Filtering grade | 40 µm |
| Regulating range | 0.15 - 0.9 MPa (20 - 130 psi) |
| Pressure type | Standard type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Differential-pressure drain |
| Bowl material | PC |
| Pressure gauge | Fitted — factory standard, Factory standard scale |
| Reflux valve | Not fitted |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. Standard type, regulating 0.15 - 0.9 MPa (20 - 130 psi). The combination has no separate bracket code — the three units couple together with their own mounting hardware. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
Model Code: Airtac GC FRL Unit GC200C06MF1K
| GC200 | G-series F.R.L. combination, 200 body — sets the port range. |
|---|---|
| C0 | Port size See datasheet. This body offers 06 = PT1/8", 08 = PT1/4". |
| (blank) | Drain: Differential-pressure drain — this also sets the regulating band (0.15 - 0.9 MPa (20 - 130 psi)). |
| (blank) | Standard type. Blank is standard, L is the low-pressure type. |
| (blank) | Pressure gauge fitted (blank). |
| (blank) | Gauge shape: Factory standard. C is round, F is square. |
| (blank) | Gauge scale: Factory standard. 1 is MPa, 2 is psi, 3 is bar. |
| (blank) | Filtering grade 40 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| (blank) | PT thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, drain, type, gauge, shape, scale, grade, thread, reflux — there is no bracket position on a combination. Constituent units, orderable separately as spares: GF200-C0 filter, GR200-C0 regulator and GL200-C0 lubricator.
Size Class & How It Differs From GFC
- GC200PT1/8" - PT1/4"
- GC300PT1/4" - PT1/2"
- GC400PT3/8" - PT1/2"
- GC600PT3/4" - PT1"
A GC is three separate units, so the filter and the regulator can each be serviced or replaced on their own. A GFC is the two-unit set, where filtering and regulating share one body — shorter, but the two functions come as one part. Both filter, regulate and lubricate.
| This model | GC200 · See datasheet · 40 µm |
|---|---|
| One size up | GC300 |
| Two-unit equivalent | GFC200-C0 |
| Build order | Filter → regulator → lubricator |
Where the Airtac GC FRL Unit GC200C06MF1K Is Used
Pneumatically actuated process valve
Prepares and protects the actuator supply on an air-operated butterfly or ball valve: the check valve holds the actuator circuit if upstream air is interrupted, while filter, regulator and lubricator condition the feed.
Assembly bench impact drivers
Feeds torque-controlled impact drivers at an assembly station with filtered, regulated, lubricated air, and the reverse valve prevents backfeed from the tool side during connect and disconnect.
Small indexing fixture on a rotary table
Supplies clamping air to an indexing fixture on a machining rotary table, holding clamp pressure steady and keeping clamp cylinders lubricated through repeated cycles.
Is the Airtac GC FRL Unit GC200C06MF1K the Right Station?
Choose this MF1K version over the plain MF1 when you want a built-in reverse/check valve to protect the downstream circuit. Porting is PT1/8, the smallest in the 200 size; step to GC300/400/600 for larger ports and flow. Manual drain (M) means condensate is released by hand and the regulator range is 0.05-0.9 MPa (7-130 psi). Filtration is the standard 40 um element, with 5 um (W) available. The embedded square gauge reads MPa; psi and bar scales are options. PT is the standard thread, with G and NPT orderable. Flow appears as curves, not a single rating, so ask us to confirm sizing against the datasheet before ordering.
Quick checklist
- ✓ Body size for your peak flow (See datasheet here)
- ✓ Element 40 µm or 5 µm
- ✓ Drain sets the regulating band
- ✓ Gauge fitted, shape and scale
- ✓ Three-unit (GC) or two-unit (GFC) layout
- ✓ Oil mist acceptable downstream
Installation & Maintenance Notes
- check Install with the airflow arrow: filter first, lubricator last.
- check Mount vertically, bowls down.
- check Keep inlet pressure at or below 1.0 MPa (145 psi).
- check Adjust only within 0.15 - 0.9 MPa (20 - 130 psi).
- check Drain condensate before the bowl fills; check the oil level.
- check Keep the station above freezing (-5 to +70 °C, unfreeze).
The PC bowls must not be cleaned with solvents — wipe them with a dry cloth. The lubricator adds an oil mist downstream of the regulator. If any branch of the line must stay oil-free, take that branch off before the lubricator, or use a GR200-C0 regulator with a GF200-C0 filter on that branch.
Airtac GC FRL Unit GC200C06MF1K FAQ
AirTAC publishes GC-series flow as curves, not as a single rated number, so we do not state a flow figure here. Send us your demand in flow and pressure and we will confirm from the datasheet on request whether the 200 size at PT1/8 is right, or whether a 300/400/600 size suits better.
K means a reverse (check) valve is fitted, so air cannot flow back toward the unit if the upstream supply drops. Everything else matches the standard MF1 build: PT1/8 port, manual-drain filter bowl, 40 um element, embedded square MPa gauge and a 0.05-0.9 MPa (7-130 psi) regulator range on this manual-drain version.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC Air-Preparation Units
Request a Quote for Airtac GC FRL Unit GC200C06MF1K
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7-8 hours.