Airtac GC FRL Unit GC200C08MF1W
The AirTAC GC FRL Unit GC200C08MF1W is a genuine G-series three-unit F.R.L. combination: a separate filter, a separate regulator and a separate lubricator assembled as one air-preparation station. It has See datasheet ports, a 40 µm element, a differential-pressure drain and regulates 0.15 - 0.9 MPa (20 - 130 psi).
- TypeF.R.L. combination (3 units)
- Port sizeSee datasheet
- Regulating range0.15 - 0.9 MPa (20 - 130 psi)
- Filtering grade40 µm
- DrainDifferential-pressure drain
- Bowl materialPC
- Pressure gaugeFitted
- ThreadPT
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac GC FRL Unit GC200C08MF1W
The GC series is AirTAC's three-piece F.R.L. combination: a separate air filter, a pressure regulator and an oil-mist lubricator assembled as one set, so a single supply drop gets water and particle removal, regulated pressure and mist lubrication in one stop. This GC200C08MF1W is the 200 size set with 1/4 in PT ports, a manual-drain filter bowl, the optional 5 um filter element and an embedded square pressure gauge reading in MPa. All bowls are polycarbonate at this size, the set runs on compressed air at up to 1.0 MPa (145 psi) inlet and -5 to 70 C (non-freezing), and with the manual drain the regulator adjusts from 0.05 to 0.9 MPa (7-130 psi).
This is a genuine AirTAC part. The G-series combination sets run from 200 through 600 sizes with ports from 1/8 in to 1 in, and can be ordered with manual, automatic or differential-pressure drains, 40 um or 5 um filtration, square or round gauges in MPa, psi or bar scales, a check valve, and PT, G (BSPP) or NPT threads. AirTAC publishes flow for this series as pressure-drop curves rather than a single rated figure, so ask us for the datasheet and we will confirm the figures for your application on request.
Airtac GC FRL Unit GC200C08MF1W Technical Specifications
| Model | Airtac GC FRL Unit GC200C08MF1W |
|---|---|
| Series | GC200 F.R.L. combination |
| Composition | Filter + regulator + lubricator (3 units) |
| Port size | See datasheet (PT thread) |
| Filtering grade | 40 µm |
| Regulating range | 0.15 - 0.9 MPa (20 - 130 psi) |
| Pressure type | Standard type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Differential-pressure drain |
| Bowl material | PC |
| Pressure gauge | Fitted — factory standard, Factory standard scale |
| Reflux valve | Not fitted |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. Standard type, regulating 0.15 - 0.9 MPa (20 - 130 psi). The combination has no separate bracket code — the three units couple together with their own mounting hardware. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
Model Code: Airtac GC FRL Unit GC200C08MF1W
| GC200 | G-series F.R.L. combination, 200 body — sets the port range. |
|---|---|
| C0 | Port size See datasheet. This body offers 06 = PT1/8", 08 = PT1/4". |
| (blank) | Drain: Differential-pressure drain — this also sets the regulating band (0.15 - 0.9 MPa (20 - 130 psi)). |
| (blank) | Standard type. Blank is standard, L is the low-pressure type. |
| (blank) | Pressure gauge fitted (blank). |
| (blank) | Gauge shape: Factory standard. C is round, F is square. |
| (blank) | Gauge scale: Factory standard. 1 is MPa, 2 is psi, 3 is bar. |
| (blank) | Filtering grade 40 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| (blank) | PT thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, drain, type, gauge, shape, scale, grade, thread, reflux — there is no bracket position on a combination. Constituent units, orderable separately as spares: GF200-C0 filter, GR200-C0 regulator and GL200-C0 lubricator.
Size Class & How It Differs From GFC
- GC200PT1/8" - PT1/4"
- GC300PT1/4" - PT1/2"
- GC400PT3/8" - PT1/2"
- GC600PT3/4" - PT1"
A GC is three separate units, so the filter and the regulator can each be serviced or replaced on their own. A GFC is the two-unit set, where filtering and regulating share one body — shorter, but the two functions come as one part. Both filter, regulate and lubricate.
| This model | GC200 · See datasheet · 40 µm |
|---|---|
| One size up | GC300 |
| Two-unit equivalent | GFC200-C0 |
| Build order | Filter → regulator → lubricator |
Where the Airtac GC FRL Unit GC200C08MF1W Is Used
Finishing booth spray guns
The 5 um element cuts fine particulate ahead of HVLP spray guns in a wood-finishing booth, while the lubricator conditions the gun needle and trigger packings.
Pneumatic panel actuators
Supplies diaphragm and cylinder actuators on a control panel with finely filtered air, and the square MPa gauge makes the line setting easy to verify.
Small press shop drop
A compact F.R.L. for a 200-size drop serving a bench press and air chucks, delivering clean, regulated, oil-misted air to the bench equipment.
Is the Airtac GC FRL Unit GC200C08MF1W the Right Station?
The 200 size with 1/4 in PT ports is the entry step of the G-series range; if your demand is beyond what the 200-size bodies pass, step up to 300 (3/8-1/2 in), 400 (1/2-3/4 in) or 600 (1 in). This set carries a manual drain, so the regulator spans 0.05-0.9 MPa (7-130 psi) and the bowl is drained by hand; the W code selects the 5 um element for finer particle removal than the standard 40 um, on the same 200-size body. The embedded square gauge reads MPa, with psi or bar scales orderable. PT is the standard thread, with G (BSPP) and NPT available as orderable options. AirTAC publishes flow as pressure-drop curves, not a single rating, so ask us to confirm sizing against your application before ordering.
Quick checklist
- ✓ Body size for your peak flow (See datasheet here)
- ✓ Element 40 µm or 5 µm
- ✓ Drain sets the regulating band
- ✓ Gauge fitted, shape and scale
- ✓ Three-unit (GC) or two-unit (GFC) layout
- ✓ Oil mist acceptable downstream
Installation & Maintenance Notes
- check Install with the airflow arrow: filter first, lubricator last.
- check Mount vertically, bowls down.
- check Keep inlet pressure at or below 1.0 MPa (145 psi).
- check Adjust only within 0.15 - 0.9 MPa (20 - 130 psi).
- check Drain condensate before the bowl fills; check the oil level.
- check Keep the station above freezing (-5 to +70 °C, unfreeze).
The PC bowls must not be cleaned with solvents — wipe them with a dry cloth. The lubricator adds an oil mist downstream of the regulator. If any branch of the line must stay oil-free, take that branch off before the lubricator, or use a GR200-C0 regulator with a GF200-C0 filter on that branch.
Airtac GC FRL Unit GC200C08MF1W FAQ
AirTAC publishes G-series flow as pressure-drop curves rather than a single rated figure, so we do not quote one number. Send us your line pressure and expected air demand and we will confirm the sizing from the datasheet on request.
The W in the code selects the optional 5 um element for finer particle removal; without the W the standard 40 um element is fitted. Both run on the same 200-size body, so the choice is about the downstream equipment, not the port size.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC Air-Preparation Units
Request a Quote for Airtac GC FRL Unit GC200C08MF1W
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7-8 hours.