Airtac GC FRL Unit GC200C08MF1WK
The AirTAC GC FRL Unit GC200C08MF1WK is a genuine G-series three-unit F.R.L. combination: a separate filter, a separate regulator and a separate lubricator assembled as one air-preparation station. It has See datasheet ports, a 40 µm element, a differential-pressure drain and regulates 0.15 - 0.9 MPa (20 - 130 psi).
- TypeF.R.L. combination (3 units)
- Port sizeSee datasheet
- Regulating range0.15 - 0.9 MPa (20 - 130 psi)
- Filtering grade40 µm
- DrainDifferential-pressure drain
- Bowl materialPC
- Pressure gaugeFitted
- ThreadPT
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac GC FRL Unit GC200C08MF1WK
The AirTAC GC series is a three-unit F.R.L. combination: a separate air filter, pressure regulator and lubricator built as one set. This GC200C08MF1WK is the 200 size with PT1/4 ports, a manual-drain filter bowl, a 5 um filter element, a square pressure gauge scaled in MPa, and a reverse/check valve fitted on the regulator. It filters water and particulate from the air, holds a set downstream pressure, and meters oil mist to downstream equipment in one assembly.
This is a genuine AirTAC part. Maximum working pressure is 1.0 MPa (145 psi), the manual-drain regulator adjusts from 0.05 to 0.9 MPa (7-130 psi), and the temperature range is -5 to 70 C, non-freezing. The 200-size bowl is polycarbonate (PC). AirTAC publishes flow for the G series as curves rather than a single rated figure, so contact us and we will confirm flow and datasheet figures for your application on request.
Airtac GC FRL Unit GC200C08MF1WK Technical Specifications
| Model | Airtac GC FRL Unit GC200C08MF1WK |
|---|---|
| Series | GC200 F.R.L. combination |
| Composition | Filter + regulator + lubricator (3 units) |
| Port size | See datasheet (PT thread) |
| Filtering grade | 40 µm |
| Regulating range | 0.15 - 0.9 MPa (20 - 130 psi) |
| Pressure type | Standard type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Differential-pressure drain |
| Bowl material | PC |
| Pressure gauge | Fitted — factory standard, Factory standard scale |
| Reflux valve | Not fitted |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. Standard type, regulating 0.15 - 0.9 MPa (20 - 130 psi). The combination has no separate bracket code — the three units couple together with their own mounting hardware. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
Model Code: Airtac GC FRL Unit GC200C08MF1WK
| GC200 | G-series F.R.L. combination, 200 body — sets the port range. |
|---|---|
| C0 | Port size See datasheet. This body offers 06 = PT1/8", 08 = PT1/4". |
| (blank) | Drain: Differential-pressure drain — this also sets the regulating band (0.15 - 0.9 MPa (20 - 130 psi)). |
| (blank) | Standard type. Blank is standard, L is the low-pressure type. |
| (blank) | Pressure gauge fitted (blank). |
| (blank) | Gauge shape: Factory standard. C is round, F is square. |
| (blank) | Gauge scale: Factory standard. 1 is MPa, 2 is psi, 3 is bar. |
| (blank) | Filtering grade 40 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| (blank) | PT thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, drain, type, gauge, shape, scale, grade, thread, reflux — there is no bracket position on a combination. Constituent units, orderable separately as spares: GF200-C0 filter, GR200-C0 regulator and GL200-C0 lubricator.
Size Class & How It Differs From GFC
- GC200PT1/8" - PT1/4"
- GC300PT1/4" - PT1/2"
- GC400PT3/8" - PT1/2"
- GC600PT3/4" - PT1"
A GC is three separate units, so the filter and the regulator can each be serviced or replaced on their own. A GFC is the two-unit set, where filtering and regulating share one body — shorter, but the two functions come as one part. Both filter, regulate and lubricate.
| This model | GC200 · See datasheet · 40 µm |
|---|---|
| One size up | GC300 |
| Two-unit equivalent | GFC200-C0 |
| Build order | Filter → regulator → lubricator |
Where the Airtac GC FRL Unit GC200C08MF1WK Is Used
Pneumatic punch press feed
Conditions the air feeding a small benchtop punch or forming press: the filter keeps punch-slide cylinder seals clean, the regulator holds consistent clamping force, and the lubricator oils the cylinder for smooth strokes.
Spray-paint gun air prep
Mounted at the wall drop feeding a paint-spray gun, the 5 um element removes fine water and dirt that would ruin a finish, while the regulator sets a stable atomising pressure and the lubricator is set for minimal or zero oil feed.
Packaging line actuator supply
Serves the diverters, pushers and sealing cylinders on a carton-packaging conveyor, supplying clean, regulated and lightly oiled air so the actuators cycle consistently through the shift.
Is the Airtac GC FRL Unit GC200C08MF1WK the Right Station?
Size 200 with 1/4 in (08) PT ports is the compact step of the G series; if your air demand outgrows a 1/4 in line, the 300, 400 and 600 sizes step up in port and capacity. This unit has a manual drain, so the bowl must be drained periodically by hand; choose an automatic or differential-pressure drain variant if that is not practical. The element here is 5 um (W) for finer filtration; the standard grade is 40 um. The regulator is the standard type with an embedded square gauge scaled in MPa (external round gauges and other scales are catalogue options), and a reverse/check valve is fitted. Thread is PT as standard; G (BSPP) and NPT are orderable options, and a bracket is included. Because flow is published as curves, not a single rating, ask us to confirm sizing against your application before ordering.
Quick checklist
- ✓ Body size for your peak flow (See datasheet here)
- ✓ Element 40 µm or 5 µm
- ✓ Drain sets the regulating band
- ✓ Gauge fitted, shape and scale
- ✓ Three-unit (GC) or two-unit (GFC) layout
- ✓ Oil mist acceptable downstream
Installation & Maintenance Notes
- check Install with the airflow arrow: filter first, lubricator last.
- check Mount vertically, bowls down.
- check Keep inlet pressure at or below 1.0 MPa (145 psi).
- check Adjust only within 0.15 - 0.9 MPa (20 - 130 psi).
- check Drain condensate before the bowl fills; check the oil level.
- check Keep the station above freezing (-5 to +70 °C, unfreeze).
The PC bowls must not be cleaned with solvents — wipe them with a dry cloth. The lubricator adds an oil mist downstream of the regulator. If any branch of the line must stay oil-free, take that branch off before the lubricator, or use a GR200-C0 regulator with a GF200-C0 filter on that branch.
Airtac GC FRL Unit GC200C08MF1WK FAQ
AirTAC publishes flow for the G series as performance curves rather than a single rated figure, so we do not quote one number here. Send us your pressure and demand details and we will confirm the flow and datasheet figures for this unit on request.
The M in the code means the filter bowl is drained by hand, which suits stations visited during normal maintenance; automatic (A) and differential-pressure (blank) drain variants exist if you cannot drain regularly. The trailing K means a reverse/check valve is fitted on the regulator, holding downstream pressure if the upstream supply is interrupted.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC Air-Preparation Units
Request a Quote for Airtac GC FRL Unit GC200C08MF1WK
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7-8 hours.