AirTAC GF200-06 Filter (GF20006MW)
The AirTAC AirTAC GF200-06 Filter (GF20006MW) is a genuine G-series air filter. It separates condensed water and filters particulate from the compressed-air line through a 5 µm element, with PT1/8" ports and a manual drain. A filter does not set downstream pressure — pair it with a GR regulator, or use a GFR filter regulator, when pressure control is needed.
- TypeAir filter
- Port sizePT1/8"
- Filtering grade5 µm
- DrainManual drain
- Inlet pressure0 - 0.9 MPa (0 - 131 psi)
- Bowl materialPC
- ThreadPT
- BracketMounting bracket included
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the AirTAC GF200-06 Filter (GF20006MW)
The GF20006MW is an AirTAC G-series air filter: filtration of water and particulate only, with no regulator and no lubricator. This size 200 unit has a PT1/8 port, the fine 5 um W element (versus the 40 um standard), and a manual drain that you open by hand to empty collected condensate. Unlike the J variant, this configuration includes the mounting bracket for fixing to a panel or frame.
This is a genuine AirTAC part in the GF family, which covers 200 through 600 sizes with optional G (BSPP) or NPT threads and automatic, manual or differential-pressure drains. Flow is published as curves rather than a single rating; we confirm datasheet figures on request.
AirTAC GF200-06 Filter (GF20006MW) Technical Specifications
| Model | AirTAC GF200-06 Filter (GF20006MW) |
|---|---|
| Series | GF200 air filter |
| Port size | PT1/8" (PT thread) |
| Filtering grade | 5 µm |
| Drain type | Manual drain |
| Bracket | Mounting bracket included |
| Fluid | Compressed air |
|---|---|
| Inlet pressure | 0 - 0.9 MPa (0 - 131 psi) |
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Bowl material | PC |
| Feature | Low pressure loss |
Specifications follow the official AirTAC G-series air-preparation data. The inlet-pressure band is set by the drain type: automatic and differential-pressure drains run 0.15 - 1.0 MPa, a manual drain runs 0 - 0.9 MPa. Air must not freeze in the unit. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
Model Code: AirTAC GF200-06 Filter (GF20006MW)
| GF200 | G-series air filter, 200 body — sets the port range. |
|---|---|
| 06 | Port size PT1/8". This body offers 06 = PT1/8", 08 = PT1/4". |
| M | Drain: Manual drain. Options are differential (blank), automatic (A) or manual (M). |
| (blank) | Mounting bracket included. A bracket ships by default; J orders it without. |
| W | Filtering grade 5 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| (blank) | PT thread. PT is the default; G is BSPP and T is NPT. |
Field order is size, port, drain, bracket, grade, thread — a blank position takes the default. Example: GF300-10AJW is a 300 body, PT3/8", automatic drain, no bracket, 5 µm element, PT thread.
Size Class
- GF200PT1/8" - PT1/4"
- GF300PT1/4" - PT1/2"
- GF400PT3/8" - PT1/2"
- GF600PT3/4" - PT1"
A larger body carries a larger port and passes more air at the same pressure drop. AirTAC publishes flow only as curves, so size the body from your peak demand with headroom rather than from a single rated figure. The GF600 uses an aluminium-alloy bowl; the 200, 300 and 400 bodies use PC.
| This model | GF200 · PT1/8" · 5 µm |
|---|---|
| One size up | GF300 |
| Line order | Filter first, then regulator, then lubricator |
Where the AirTAC GF200-06 Filter (GF20006MW) Is Used
Belt conveyor controls
Filtered air for the pneumatic reject pushers and stop gates on a small belt-conveyor sorting station, with the bracket fixing the unit to the frame.
Wire and cable machinery
Fine particulate removal on the air feed to air-wipe and blowing stations on a small wire-drawing or cable line.
Machine-shop air drops
Point-of-use 5 um filtration at an individual machine drop, shielding the machine's own valve stack from water and grit in the shop main.
Is the AirTAC GF200-06 Filter (GF20006MW) the Right Filter?
The 5 um element suits lines feeding finer-tolerance equipment; the 40 um standard element is the lower-cost choice for general pre-filtration. Size 200 with a 1/8 in port serves compact lines - step up a size for higher line demand. Manual drain fits installations with periodic operator attention; choose automatic or differential-pressure drain for unattended locations. The included bracket lets you bolt the unit down rather than hanging it on the pipe.
Flow is published as curves, not a single rating, so ask us to confirm sizing against your application before ordering. PT is the standard thread; G (BSPP) and NPT are catalogue options to order.
Quick checklist
- ✓ Body size for your peak flow (PT1/8" here)
- ✓ Element 40 µm or 5 µm
- ✓ Drain: differential, automatic or manual
- ✓ Manual drain caps inlet at 0.9 MPa
- ✓ Thread PT, G (BSPP) or NPT
- ✓ Bracket needed, or order with J
Installation & Maintenance Notes
- check Mount vertically, bowl down, and follow the airflow arrow.
- check Put the filter first in the air-preparation line.
- check Keep inlet pressure within 0 - 0.9 MPa (0 - 131 psi).
- check Drain condensate before the bowl fills.
- check Keep the unit above freezing (-5 to +70 °C, unfreeze).
- check Replace the 5 µm element when pressure loss rises.
The PC bowl must not be cleaned with solvents or exposed to synthetic oils that attack polycarbonate — wipe it with a dry cloth. A filter removes water and particulate only; it does not regulate pressure or add lubrication.
AirTAC GF200-06 Filter (GF20006MW) FAQ
AirTAC publishes filter flow as curves across the pressure range rather than a single rated figure, so there is no one number we can state. Give us your line pressure and demand and we will confirm the datasheet and flow curve for this exact model on request before you order.
Yes - unlike the J-suffix variant, this code carries the mounting bracket, so you can secure the filter to a panel or machine frame instead of relying on the pipework alone. A mounted bowl is less likely to be stressed by pipe loads or knocks.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC Air-Preparation Units
Request a Quote for AirTAC GF200-06 Filter (GF20006MW)
Send us the quantity, thread type (PT / G / NPT) and destination. We confirm price, availability and lead time — usually within 7-8 hours.