AirTAC GF200-06 Filter (GF20006W)
The AirTAC AirTAC GF200-06 Filter (GF20006W) is a genuine G-series air filter. It separates condensed water and filters particulate from the compressed-air line through a 5 µm element, with PT1/8" ports and a differential-pressure drain. A filter does not set downstream pressure — pair it with a GR regulator, or use a GFR filter regulator, when pressure control is needed.
- TypeAir filter
- Port sizePT1/8"
- Filtering grade5 µm
- DrainDifferential-pressure drain
- Inlet pressure0.15 - 1.0 MPa (22 - 145 psi)
- Bowl materialPC
- ThreadPT
- BracketMounting bracket included
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the AirTAC GF200-06 Filter (GF20006W)
The GF20006W is an AirTAC G-series air filter that removes water and particulate from compressed air - nothing more. No regulator, no lubricator. This size 200 unit has a PT1/8 port and the fine 5 um W element (versus the 40 um standard). With no drain letter, it carries the default differential-pressure drain, which opens the bowl drain automatically once the pressure drop across the element reaches its threshold.
This is a genuine AirTAC part in the GF family, spanning 200/300/400/600 sizes with G (BSPP) or NPT thread options and automatic, manual or differential-pressure drains, bracket included as standard here. Flow is published as curves rather than a single rating; we confirm datasheet figures on request.
AirTAC GF200-06 Filter (GF20006W) Technical Specifications
| Model | AirTAC GF200-06 Filter (GF20006W) |
|---|---|
| Series | GF200 air filter |
| Port size | PT1/8" (PT thread) |
| Filtering grade | 5 µm |
| Drain type | Differential-pressure drain |
| Bracket | Mounting bracket included |
| Fluid | Compressed air |
|---|---|
| Inlet pressure | 0.15 - 1.0 MPa (22 - 145 psi) |
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Bowl material | PC |
| Feature | Low pressure loss |
Specifications follow the official AirTAC G-series air-preparation data. The inlet-pressure band is set by the drain type: automatic and differential-pressure drains run 0.15 - 1.0 MPa, a manual drain runs 0 - 0.9 MPa. Air must not freeze in the unit. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
Model Code: AirTAC GF200-06 Filter (GF20006W)
| GF200 | G-series air filter, 200 body — sets the port range. |
|---|---|
| 06 | Port size PT1/8". This body offers 06 = PT1/8", 08 = PT1/4". |
| (blank) | Drain: Differential-pressure drain. Options are differential (blank), automatic (A) or manual (M). |
| (blank) | Mounting bracket included. A bracket ships by default; J orders it without. |
| W | Filtering grade 5 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| (blank) | PT thread. PT is the default; G is BSPP and T is NPT. |
Field order is size, port, drain, bracket, grade, thread — a blank position takes the default. Example: GF300-10AJW is a 300 body, PT3/8", automatic drain, no bracket, 5 µm element, PT thread.
Size Class
- GF200PT1/8" - PT1/4"
- GF300PT1/4" - PT1/2"
- GF400PT3/8" - PT1/2"
- GF600PT3/4" - PT1"
A larger body carries a larger port and passes more air at the same pressure drop. AirTAC publishes flow only as curves, so size the body from your peak demand with headroom rather than from a single rated figure. The GF600 uses an aluminium-alloy bowl; the 200, 300 and 400 bodies use PC.
| This model | GF200 · PT1/8" · 5 µm |
|---|---|
| One size up | GF300 |
| Line order | Filter first, then regulator, then lubricator |
Where the AirTAC GF200-06 Filter (GF20006W) Is Used
Air bearing and air table supply
Fine, continuously drained filtration on the feed to small air-bearing or air-table surfaces, where dirt in the orifices degrades the air film.
Pneumatic instrumentation
Clean supply air to positioners and pneumatic instrument loops on process skids, with the differential drain handling condensate between service visits.
Process valve actuation
Filtered air to small pneumatic actuated valves on a compact process line, keeping the actuator and pilot valve free of water and fine grit.
Is the AirTAC GF200-06 Filter (GF20006W) the Right Filter?
Pick the 5 um W element when the downstream equipment needs finer air than the 40 um standard provides. The differential-pressure drain (the blank default) discharges condensate on its own as the element loads - the hands-off middle ground between manual and fully automatic drains. Size 200 with a 1/8 in port is the compact G-series step; choose 300/400/600 for larger lines. Bracket included in this configuration.
Flow is published as curves, not a single rating, so ask us to confirm sizing against your application before ordering. PT is the standard thread; G (BSPP) and NPT are catalogue options to order.
Quick checklist
- ✓ Body size for your peak flow (PT1/8" here)
- ✓ Element 40 µm or 5 µm
- ✓ Drain: differential, automatic or manual
- ✓ Manual drain caps inlet at 0.9 MPa
- ✓ Thread PT, G (BSPP) or NPT
- ✓ Bracket needed, or order with J
Installation & Maintenance Notes
- check Mount vertically, bowl down, and follow the airflow arrow.
- check Put the filter first in the air-preparation line.
- check Keep inlet pressure within 0.15 - 1.0 MPa (22 - 145 psi).
- check Drain condensate before the bowl fills.
- check Keep the unit above freezing (-5 to +70 °C, unfreeze).
- check Replace the 5 µm element when pressure loss rises.
The PC bowl must not be cleaned with solvents or exposed to synthetic oils that attack polycarbonate — wipe it with a dry cloth. A filter removes water and particulate only; it does not regulate pressure or add lubrication.
AirTAC GF200-06 Filter (GF20006W) FAQ
AirTAC does not publish a single rated flow for this filter - performance is given as flow curves across the pressure range. Send us your operating pressure and air demand and we will confirm the datasheet and the sizing against your application on request before you order.
With no drain letter, this filter uses the default differential-pressure drain: as the 5 um element loads with dirt, the pressure drop across it rises and trips the drain to discharge condensate automatically. Manual drain empties only when opened by hand; the A code is a separate automatic-drain mechanism.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC Air-Preparation Units
Request a Quote for AirTAC GF200-06 Filter (GF20006W)
Send us the quantity, thread type (PT / G / NPT) and destination. We confirm price, availability and lead time — usually within 7-8 hours.