Airtac GTFR Filter Regulator GTFR20008SJW
Genuine AirTAC filter regulator, order code GTFR20008SJW from the GTFR200 range. The options this code selects are decoded below; series data follow the official AirTAC catalog.
- Port1/4" (08)
- Type · gaugeStandard (S) · With gauge (MPa/psi)
- ConfigurationNo bracket (J) · 5 µm element (W) · PT thread
- Port1/8" (06), 1/4" (08)
- ThreadPT (standard)
- Filter element40 µm (standard), 5 µm (W)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac GTFR Filter Regulator GTFR20008SJW
This code pairs the two things operators check most often: a pressure gauge on top and the 5 um element (W) inside. The gauge-fitted build lets you dial in downstream pressure on the spot, while the 5 um element goes beyond the standard 40 um filtration that GTFR200 ships with by default. Port size is 1/4" (08) with PT thread, the GT200 standard.
The J in the code means no mounting bracket, so the unit hangs directly on its 1/4" piping or on your own hardware. The bowl is the short PC bowl that defines the GT200 series - the compact answer to the GA200 for cramped cabinets - and it empties by differential plus manual drain, so check it as part of routine service rather than expecting automatic discharge.
Airtac GTFR Filter Regulator GTFR20008SJW Technical Specifications
| Order code | GTFR20008SJW |
|---|---|
| Product | Filter Regulator |
| Port | 1/4" (08) |
| Type · gauge | Standard (S) · With gauge (MPa/psi) |
| Configuration | No bracket (J) · 5 µm element (W) · PT thread |
| Port | 1/8" (06), 1/4" (08) |
|---|---|
| Thread | PT (standard) |
| Filter element | 40 µm (standard), 5 µm (W) |
| Bowl | Short PC bowl |
| Drain | Differential + manual |
| Fluid | Air |
| Low-pressure (L) version | 0.15 – 0.4 MPa (20 – 58 psi) |
Source: AirTAC Products Catalog 2026A (p.235, PDF01-P0237), GT200 ordering code and specifications.
How to choose
GTFR20008SJW is the choice when you want visible, adjustable pressure but your circuit has no backflow concern - for that protection add K and step to GTFR20008SJWK, or drop the gauge for GTFR20008SJNWK. If 40 um filtration is sufficient, GTFR20008SJ is the cheaper sibling with the same gauge and no-bracket layout. Other neighbours: GTFR20008SJWT for NPT thread, GTFR20008SLJW for the 0.15 - 0.4 MPa (20 - 58 psi) low-pressure type, and bracket-included builds without the J.
Applications
Bench setup of small actuators
On a test bench or during commissioning, the fitted gauge lets a technician read and trim the regulated pressure for 1/4" PT-threaded tooling while the 5 um element protects fine control valves.
Laboratory and pilot rigs
Clean 5 um air and an on-unit gauge suit compact lab skids where the short PC bowl has to squeeze into tight frames and the J no-bracket build ties straight into existing pipework.
Packaging machine air feed
Packaging lines run many small cylinders; a gauge-equipped regulator at each drop makes per-station pressure visible, and the 5 um element keeps downstream poppet and spool valves clean.
FAQ
What are the key figures of GTFR20008SJW?
Port 1/4" (08), PT thread, standard pressure type, 5 um filter element, pressure gauge fitted, no mounting bracket (J), short PC bowl with differential plus manual drain, fluid air. The low-pressure L version of the series regulates 0.15 - 0.4 MPa (20 - 58 psi).
How does the W element change maintenance?
W replaces the standard 40 um element with a 5 um one, so the air downstream is cleaner for sensitive components. The finer element loads up faster, so inspect it when you manually drain the short PC bowl; if your circuit tolerates 40 um, the plain GTFR20008SJ needs that attention less often.