
The AirTAC JSID Double Rod Cylinder JSID125X1000S is a genuine double acting, double rod JIS-standard air cylinder with a Ø125mm bore and 1000mm stroke, G1/2 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
Delivering 5734 N of thrust in both directions at 0.5 MPa, this 125 mm bore double-rod actuator uses a single piston with a rod exiting each cover to ensure perfectly symmetric load paths. The G1/2 ported hard-anodized aluminum profile barrel keeps the total body shorter than a same-bore ISO 15552 unit.
Because the piston sees the same annular area on both faces, push and pull forces remain identical at 8028 N when running at 0.7 MPa. The -S suffix means a built-in magnet allows CMSE/DMSE sensors to drop directly into the side grooves for precise end-position detection. Note that the adjustable 33 mm air cushions only decelerate the load near the stroke ends; an external rod lock or pilot-operated check valve is required to hold a load securely during air loss.
| Model | Airtac JSID Double Rod Cylinder JSID125X1000S |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø125 mm |
| Stroke | 1000 mm |
| Acting type | Double acting, double rod |
| Port size | G1/2 |
| Rod thread | M27×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 33 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 5734 N | 5734 N |
| 0.7 MPa | 8027 N | 8027 N |
| Max (@1.0 MPa) | 1169 kgf | |
Double-rod: the rod passes through both covers, so output force is equal in both directions.
| JSID | JIS-standard profile cylinder (double-rod type). |
|---|---|
| 125 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×1000 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Drives two synchronized forming tools from opposite rod ends, ensuring parallel impact and equal 5734 N clamping force on both sides of the workpiece.
Shifts heavy material loads across a belt line using both rod ends to maintain a balanced drive and avoid binding over the 1000 mm travel.
Sizing around the 125 mm bore, the adjacent 100 mm option yields 3574 N each way at 0.5 MPa, while the 125 mm sits at the top of the range with 5734 N. Choose this double-rod configuration when your application demands anti-rotation stability, symmetric load distribution, or the ability to drive twin tooling from both ends simultaneously. Mounting options include Basic, FA, LB, TC, TCM1, and TCM2. The -S magnet supports CMSE/DMSE switches. Since this unit features a 1000 mm stroke, external guide rails are strongly recommended to prevent rod bending and absorb side loads over that extended length.
Quick checklist
The force is equal in both directions due to the double-rod design: 5734 N at 0.5 MPa, 8028 N at 0.7 MPa, and a theoretical maximum of 1169 kgf at 1.0 MPa. Operating speed ranges from 30-500 mm/s. It features a G1/2 port, M27x2.0 rod thread, and 33 mm adjustable air cushions at both ends.
No, the air cushions only decelerate the piston near the end of the stroke and do not act as a brake. The piston will drift if air pressure is lost or the valve is centered. To hold a load securely, you must install an external rod lock or a pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.