
The AirTAC JSID Double Rod Cylinder JSID125X200S is a genuine double acting, double rod JIS-standard air cylinder with a Ø125mm bore and 200mm stroke, G1/2 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
Delivering 5734 N of thrust in both directions at 0.5 MPa, this AirTAC double-rod actuator uses a 125 mm bore and a 200 mm stroke to drive heavy symmetrical loads. The twin-rod architecture creates an identical pressure area on each piston face, ensuring perfectly balanced push and pull forces while preventing rotation. Because the extruded hard-anodized aluminum profile barrel omits traditional retaining rods, the overall body is significantly shorter and more compact than a same-bore ISO 15552 cylinder.
This JSID125X200S variant includes a built-in piston magnet for CMSE or DMSE reed and electronic switches that mount directly into the side grooves. The unit features a G1/2 air port, a 33 mm adjustable air cushion at each end, and a piston rod diameter of 32 mm. Remember that the cushions only decelerate the load near the stroke ends; an external rod lock or pilot-operated check valve is required to hold a load securely on air loss.
| Model | Airtac JSID Double Rod Cylinder JSID125X200S |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø125 mm |
| Stroke | 200 mm |
| Acting type | Double acting, double rod |
| Port size | G1/2 |
| Rod thread | M27×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 33 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 5734 N | 5734 N |
| 0.7 MPa | 8027 N | 8027 N |
| Max (@1.0 MPa) | 1169 kgf | |
Double-rod: the rod passes through both covers, so output force is equal in both directions.
| JSID | JIS-standard profile cylinder (double-rod type). |
|---|---|
| 125 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Drives two parallel machining spindles simultaneously from both rod ends, using the equal 5734 N bidirectional force to raise and lower heavy metal fixtures without rotational twist.
Moves a heavy 292 kg vertical pallet load in a high-speed sorting hub, relying on the balanced push and pull thrust to maintain precise alignment during rapid reversals.
Ejects formed metal parts from a stamping press using both rod ends, where the compact JIS profile saves valuable floor space compared to larger standard ISO 15552 units.
When sizing this series, sizing both ways is essential: stepping down to the 100 mm bore yields 3574 N each way at 0.5 MPa, while the 125 mm bore used here sits at the top edge with 5734 N. A double-rod design is the right call when your mechanism demands anti-rotation guidance, needs to drive twin tooling from both ends simultaneously, or requires a symmetric load path with back-end sensor cam tracking. Mounting options for this JIS profile include Basic, FA, LB, TC, TCM1, and TCM2. The included -S magnet enables precise position sensing via CMSE/DMSE switches. For this 200 mm stroke, ensure external guide rails are used to absorb any lateral side loads and prevent binding.
Quick checklist
Because the rod exits both ends, the push and pull forces are equal: 5734 N at 0.5 MPa and 8028 N at 0.7 MPa. The theoretical maximum force is 1169 kgf at 1.0 MPa. It operates at 30-500 mm/s, features a G1/2 port, and has a 33 mm adjustable cushion at each end.
No, a plain double-rod cylinder will drift and cannot hold a load without live air pressure, as the air cushions only decelerate the piston near the stroke ends. To maintain a vertical position safely during air loss or valve centering, you must install an external rod lock or a pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.