
The AirTAC JSID Double Rod Cylinder JSID125X25S is a genuine double acting, double rod JIS-standard air cylinder with a Ø125mm bore and 25mm stroke, G1/2 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
Delivering 5734 N of equal force in both directions at 0.5 MPa, this large-bore double-rod actuator uses a G1/2 port and a 32 mm piston rod that exits both ends. The symmetric layout provides a non-rotating anti-twist load path, allowing you to drive twin tooling or mount a rear sensor cam without extra linkage. Built to JIS standards with an extruded hard-anodized aluminum profile barrel, it is significantly shorter and more compact than an ISO 15552 cylinder of the same bore.
The integrated -S piston magnet allows CMSE/DMSE switches to drop directly into the side grooves for precise position sensing. Adjustable 33 mm air cushions at both ends tame the kinetic energy of this heavy piston, though a plain cylinder drifts on air loss, so fit an external rod lock or pilot-operated check valve if you need to hold a suspended load.
| Model | Airtac JSID Double Rod Cylinder JSID125X25S |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø125 mm |
| Stroke | 25 mm |
| Acting type | Double acting, double rod |
| Port size | G1/2 |
| Rod thread | M27×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 33 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 5734 N | 5734 N |
| 0.7 MPa | 8027 N | 8027 N |
| Max (@1.0 MPa) | 1169 kgf | |
Double-rod: the rod passes through both covers, so output force is equal in both directions.
| JSID | JIS-standard profile cylinder (double-rod type). |
|---|---|
| 125 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×25 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Drives two forming tools simultaneously with equal 5734 N force, using the symmetric rod layout to maintain parallelism and prevent twist under heavy load.
Uses the protruding rear rod to push a diverter while the front rod carries a sensor cam, tracking position via CMSE switches in the side grooves.
Sizing this actuator requires balancing your space and force needs against the neighboring options. Stepping down to a 100 mm bore yields 3574 N each way, whereas this 125 mm unit provides 5734 N at 0.5 MPa, sitting at the top of the range for heavy-duty cycles. Choose the double-rod configuration when your mechanism demands anti-rotation guidance, symmetric load distribution, or simultaneous actuation from both ends. Mounting options include Basic, FA, LB, TC, TCM1, and TCM2 brackets. The -S magnet equips it for CMSE/DMSE sensors. Because the stroke is only 25 mm, side-load stress is minimal, but any application exceeding 300 mm of travel should incorporate an external guide to prevent binding.
Quick checklist
Because the 32 mm rod exits both ends, force is equal in both directions: 5734 N at 0.5 MPa and 8028 N at 0.7 MPa. The theoretical max is 1169 kgf at 1.0 MPa. Operating speed ranges from 30-500 mm/s. It uses a G1/2 port and M27x2.0 rod thread.
The extruded hard-anodized aluminum profile barrel makes it shorter and more compact than a same-bore ISO 15552 cylinder. A plain cylinder does not hold load on air loss, as the cushions only decelerate; use an external rod lock or pilot-operated check valve for holding. The -S variant includes a magnet for CMSE/DMSE sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.