
The AirTAC JSID Double Rod Cylinder JSID125X300 is a genuine double acting, double rod JIS-standard air cylinder with a Ø125mm bore and 300mm stroke, G1/2 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
Delivering 5734 N of thrust in both directions at 0.5 MPa, this 125 mm bore double-rod actuator uses a symmetric piston layout to eliminate push-pull force disparity. The G1/2 ported hard-anodized aluminum profile body is a JIS-standard build, measurably shorter and more compact than a same-bore ISO 15552 cylinder. A rod extends from each end, creating an anti-twist load path that simultaneously drives two stations or carries a rear sensor cam.
This non-magnet SKU cannot host reed switches; add the -S variant for CMSE/DMSE sensing. Note that the 33 mm adjustable air cushions only decelerate the load near stroke end, so fit an external rod lock or pilot-operated check valve if you need to hold position against gravity.
| Model | Airtac JSID Double Rod Cylinder JSID125X300 |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø125 mm |
| Stroke | 300 mm |
| Acting type | Double acting, double rod |
| Port size | G1/2 |
| Rod thread | M27×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 33 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 5734 N | 5734 N |
| 0.7 MPa | 8027 N | 8027 N |
| Max (@1.0 MPa) | 1169 kgf | |
Double-rod: the rod passes through both covers, so output force is equal in both directions.
| JSID | JIS-standard profile cylinder (double-rod type). |
|---|---|
| 125 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×300 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Drives two opposing machining heads simultaneously from a single symmetric piston, ensuring perfectly matched feed rates and equal 5734 N thrust on both strokes.
Uses the dual-rod architecture to push heavy pallets along a conveyor without the mechanical twist or yaw common to single-rod actuators under high offset loads.
Lifts and lowers heavy material racks with equal force both ways, relying on the compact JIS profile to save vertical machine space compared to standard ISO units.
Sizing this actuator requires balancing your load against the available bores. Stepping down, the 100 mm bore provides 3574 N both ways, while this 125 mm unit tops the range at 5734 N at 0.5 MPa. Choose the double-rod format when your mechanism demands anti-rotation guidance, symmetric load distribution, or twin tooling driven from one piston. Mounting options include FA, LB, TC, TCM1, and TCM2 brackets. Because this 300 mm stroke invites rod sag and bending under offset loads, always support the mechanism with external linear guides to prevent premature seal wear. This base model lacks a magnet and cannot accept sensors; specify the -S version if your control system requires CMSE or DMSE position detection.
Quick checklist
Because the rod passes through both covers, force is equal in both directions: 5734 N at 0.5 MPa and 8028 N at 0.7 MPa, with a theoretical max of 1169 kgf at 1.0 MPa. Operating speed ranges from 30-500 mm/s. It features a G1/2 port and a 32 mm piston rod.
No. The 33 mm adjustable air cushions only decelerate the piston near the stroke ends; they do not lock the position. If your application requires load holding on loss of air or valve centering, you must install an external rod lock or a pilot-operated check valve.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.