
The AirTAC JSID Double Rod Cylinder JSID125X450 is a genuine double acting, double rod JIS-standard air cylinder with a Ø125mm bore and 450mm stroke, G1/2 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
Delivering 5734 N of thrust in both directions at 0.5 MPa, this 125 mm bore double-rod actuator uses a single piston with a rod exiting each end to ensure perfectly symmetric load paths. The twin rods prevent rotation and allow you to drive two mechanisms simultaneously from one centerline. Built to JIS standards with an extruded hard-anodized aluminum profile barrel, the body is noticeably shorter and more compact than a same-bore ISO 15552 cylinder.
This specific SKU lacks a piston magnet, so it cannot accept CMSE or DMSE position sensors without upgrading to the -S variant. The adjustable 33 mm air cushions at both ends decelerate the heavy payload smoothly, but an external rod lock or pilot-operated check valve is required to hold a load securely during air loss.
| Model | Airtac JSID Double Rod Cylinder JSID125X450 |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø125 mm |
| Stroke | 450 mm |
| Acting type | Double acting, double rod |
| Port size | G1/2 |
| Rod thread | M27×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 33 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 5734 N | 5734 N |
| 0.7 MPa | 8027 N | 8027 N |
| Max (@1.0 MPa) | 1169 kgf | |
Double-rod: the rod passes through both covers, so output force is equal in both directions.
| JSID | JIS-standard profile cylinder (double-rod type). |
|---|---|
| 125 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×450 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Drives two opposing machining spindles simultaneously with 5734 N of equal force, using the dual rods to maintain strict parallelism and prevent torsional deflection.
Shifts a heavy 450 mm transfer gate from the center outward, utilizing the equal push and pull thrust to manage bidirectional material flow without stroke imbalance.
Pushes loaded pallets from either side of a sorting line, relying on the 125 mm bore and 33 mm adjustable cushions to stop the 450 mm travel smoothly.
Sizing this actuator requires comparing the equal-both-ways force against neighboring bores: the 100 mm bore yields 3574 N at 0.5 MPa, while this 125 mm bore tops the range at 5734 N, making it the high edge for heavy applications. Choose the double-rod configuration when your setup demands anti-rotation guidance, twin tooling on opposite sides, or a symmetric load distribution. Mounting options include Basic, FA, LB, TC, TCM1, and TCM2 brackets. Because this model has no -S magnet, you must rely on external proximity sensors for position detection. For the 450 mm stroke, always support the load with an external linear guide to prevent rod bending and excessive side loading.
Quick checklist
Because the rod passes through both covers, force is equal in both directions: 5734 N at 0.5 MPa and 8028 N at 0.7 MPa, with a theoretical max of 1169 kgf at 1.0 MPa. It operates at 30-500 mm/s, features a G1/2 port, and has a 33 mm adjustable air cushion at each end.
No, this SKU lacks a piston magnet, so it cannot accept CMSE or DMSE switches. Additionally, the air cushions only decelerate the piston near stroke end; they do not hold load. For vertical or suspended loads, you must install an external rod lock or pilot-operated check valve to prevent drifting.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.