Airtac JSID Double Rod Cylinder JSID40X600
The AirTAC JSID Double Rod Cylinder JSID40X600 is a genuine double acting, double rod JIS-standard air cylinder with a Ø40mm bore and 600mm stroke, G1/4 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ40 mm
- Stroke600 mm
- Port sizeG1/4
- Acting typeDouble acting, double rod
- Rod threadM14×1.5
- CushionAdjustable, 20.5 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSID Double Rod Cylinder JSID40X600
Delivering 528 N of output force in both directions at 0.5 MPa, this 40 mm bore double-rod cylinder uses a single piston with a rod exiting each cover. Because the pressure area is identical on both faces, push and pull forces remain perfectly equal. This symmetric load path prevents piston twist and provides non-rotating anti-twist guidance for precision tasks. The extruded hard-anodized aluminum profile barrel contains no external tie rods, making the JIS-standard body noticeably shorter and more compact than a same-bore ISO 15552 cylinder.
Air enters via a G1/4 port, and adjustable 20.5 mm air cushions at both ends decelerate the piston smoothly. Note that this specific SKU lacks a magnet and cannot accept CMSE or DMSE sensors; you would need the -S variant for position detection. Furthermore, a plain cylinder does not hold load on air loss—the cushion only decelerates near stroke end, so fit an external rod lock or pilot-operated check valve for suspended loads.
Airtac JSID Double Rod Cylinder JSID40X600 Technical Specifications
| Model | Airtac JSID Double Rod Cylinder JSID40X600 |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø40 mm |
| Stroke | 600 mm |
| Acting type | Double acting, double rod |
| Port size | G1/4 |
| Rod thread | M14×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 20.5 mm |
| Max standard stroke | Up to 1200 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø40mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | 739 N |
| Max (@1.0 MPa) | 108 kgf | |
Double-rod: the rod passes through both covers, so output force is equal in both directions.
Model Code: Airtac JSID Double Rod Cylinder JSID40X600
| JSID | JIS-standard profile cylinder (double-rod type). |
|---|---|
| 40 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSID Double Rod Cylinder JSID40X600 Is Used
Twin-Tool Transfer
Uses the rod extending from both ends to push and pull a workpiece simultaneously across a 600 mm transfer station.
Symmetric Lift Station
Exploits the equal both-ways force to raise and lower a 27 kg fixture with a balanced, non-rotating load path.
Guided Edge Guide
Relies on the dual rods for anti-twist guidance while external rails absorb side-load on the long 600 mm extension.
Is the Airtac JSID Double Rod Cylinder JSID40X600 the Right Cylinder?
Sizing this 40 mm bore (528 N both ways at 0.5 MPa) against its neighbors helps confirm the fit: step down to a 32 mm bore for 345 N, or up to a 50 mm bore for 825 N if you need more push. A double-rod design is the right call when your mechanism requires anti-rotation stability, needs to drive two tools from one actuator, or benefits from a symmetric load path with back-end sensing. Mounting options include Basic, FA, LB, TC, TCM1, and TCM2 brackets. Because this is a non-magnetized model, it cannot take sensors; specify the -S version if you require CMSE or DMSE switches. With a 600 mm stroke, you must support the load with external guides to prevent rod bending and excessive side-loading.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSID Double Rod Cylinder JSID40X600 FAQ
The G1/4 ported 40 mm bore provides equal force both ways: 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a theoretical maximum of 108 kgf at 1.0 MPa. It never quotes a larger single-rod push value because both faces use the rod-side area.
This SKU lacks a magnet and cannot take CMSE or DMSE sensors; you need the -S variant for switches. Also, the air cushion only decelerates the piston—it does not hold load on air loss. For suspended loads, install an external rod lock or pilot-operated check valve.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSID Double Rod Cylinder JSID40X600
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.