Airtac JSID Double Rod Cylinder JSID80X100S
The AirTAC JSID Double Rod Cylinder JSID80X100S is a genuine double acting, double rod JIS-standard air cylinder with a Ø80mm bore and 100mm stroke, G3/8 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ80 mm
- Stroke100 mm
- Port sizeG3/8
- Acting typeDouble acting, double rod
- Rod threadM22×1.5
- CushionAdjustable, 29 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSID Double Rod Cylinder JSID80X100S
Delivering 2268 N of equal force in both directions at 0.5 MPa, this 80 mm bore double-rod actuator uses a symmetric piston design to prevent twisting under offset loads. A rod exits each end, allowing you to drive twin tooling stations or mount a rear sensor cam simultaneously. The extruded hard-anodized aluminium profile barrel keeps the unit shorter and more compact than a same-bore ISO 15552 cylinder, while the G3/8 port handles the required airflow.
The -S suffix indicates a built-in piston magnet for CMSE/DMSE switches that drop directly into the side grooves. Remember that the adjustable 29 mm air cushions only decelerate the piston near stroke end; a plain cylinder drifts on air loss, so fit an external rod lock or pilot-operated check valve if you need to hold a load.
Airtac JSID Double Rod Cylinder JSID80X100S Technical Specifications
| Model | Airtac JSID Double Rod Cylinder JSID80X100S |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 100 mm |
| Acting type | Double acting, double rod |
| Port size | G3/8 |
| Rod thread | M22×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2268 N | 2268 N |
| 0.7 MPa | 3175 N | 3175 N |
| Max (@1.0 MPa) | 463 kgf | |
Double-rod: the rod passes through both covers, so output force is equal in both directions.
Model Code: Airtac JSID Double Rod Cylinder JSID80X100S
| JSID | JIS-standard profile cylinder (double-rod type). |
|---|---|
| 80 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×100 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSID Double Rod Cylinder JSID80X100S Is Used
Twin-Station Transfer
Drives two opposing pick-and-place grippers simultaneously from one piston, keeping cycle times synchronized without adding a second valve.
Anti-Rotation Edge Guide
Uses the dual rods exiting both covers to resist twist and maintain precise vertical alignment when guiding heavy sheet metal through a press.
Rear-Cam Position Sensing
Mounts a CMSE/DMSE sensor target on the back rod while the front rod handles the primary 116 kg vertical lift duty.
Is the Airtac JSID Double Rod Cylinder JSID80X100S the Right Cylinder?
Size this 80 mm bore against its neighbours: the 63 mm yields 1402 N each way, and the 100 mm provides 3574 N, both at 0.5 MPa. Choose this double-rod configuration when your mechanism demands anti-rotation stability, a symmetric load path, or rear-end sensing alongside front-end work. Mounting options include Basic, FA, LB, TC, TCM1, and TCM2 brackets. The -S magnet enables CMSE/DMSE switch integration. For any stroke at or over 300 mm, support the rod externally to prevent excessive side-loading and premature seal wear.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSID Double Rod Cylinder JSID80X100S FAQ
Because the rod passes through both covers, force is equal in both directions. It produces 2268 N at 0.5 MPa and 3175 N at 0.7 MPa each way, with a theoretical maximum of 463 kgf at 1.0 MPa. The bore uses a G3/8 port.
The dual rods create a symmetric load path that prevents rotation and allows you to drive a secondary tool or sensor cam from the back end. The -S suffix adds a piston magnet for CMSE/DMSE switches, giving you electronic or reed position feedback without external physical stops.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSID Double Rod Cylinder JSID80X100S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.