Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X200-10S
The AirTAC JSIJ63~80 Adjustable Cylinder JSIJ63X200-10S is a genuine double acting, double rod, adjustable stroke JIS-standard air cylinder with a Ø63mm bore and 200mm stroke, G3/8 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ63 mm
- Stroke200 mm
- Port sizeG3/8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM18×1.5
- CushionAdjustable, 29 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X200-10S
The external stop screw lets you trim the extend stroke by up to 10 mm, giving a usable 190 to 200 mm range while the retract end stays fixed. You can fine-tune the end position without physically swapping the cylinder, which is invaluable for dialing in machine stops or sharing spares across slightly different stroke variants. The built-in -S magnet supports CMSE/DMSE sensors that drop directly into the side grooves for precise position detection.
Built as a JIS-standard profile cylinder, the hard-anodized aluminum barrel makes it shorter and more compact than a same-bore ISO 15552 unit. Piped via a G3/8 port with a 20 mm rod and M18x1.5 thread, it runs at 30-800 mm/s. Remember that a standard cylinder drifts on air loss; the adjustable cushion only decelerates near the end, so fit an external rod lock or pilot-operated check valve if you need to hold a suspended load.
Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X200-10S Technical Specifications
| Model | Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X200-10S |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 200 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | G3/8 |
| Rod thread | M18×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | 1962 N |
| Max (@1.0 MPa) | 286 kgf | |
JSIJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative).
Model Code: Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X200-10S
| JSIJ | JIS-standard profile cylinder (adjustable-stroke type). |
|---|---|
| 63 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X200-10S Is Used
Machine Stop Calibration
Dial in exact clamping end positions on-site using the 10 mm extend stroke window without changing the entire actuator assembly.
Is the Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X200-10S the Right Cylinder?
The JSIJ series supports Basic, FA, LB, TC, TCM1, and TCM2 mounts. The included -S magnet works seamlessly with CMSE/DMSE switches. For any stroke at or over 300 mm, always use a guide rail to prevent side-load damage to the piston rod.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X200-10S FAQ
This 63 mm bore cylinder pushes 1559 N and pulls 1402 N at 0.5 MPa. At 0.7 MPa it pushes 2182 N and pulls 1962 N. The theoretical maximum force is 318 kgf at 1.0 MPa. It uses a G3/8 port, a 20 mm rod, an M18x1.5 rod thread, and has 29 mm adjustable air cushions at both ends.
The nominal 200 mm stroke is the maximum length. An external stop screw lets you shorten the extend stroke on-site by up to 10 mm, giving a usable extend range of 190 to 200 mm while the retract end remains fixed. This stop sets the end position and is not a load lock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X200-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.