Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X25-10
The AirTAC JSIJ63~80 Adjustable Cylinder JSIJ63X25-10 is a genuine double acting, double rod, adjustable stroke JIS-standard air cylinder with a Ø63mm bore and 25mm stroke, G3/8 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ63 mm
- Stroke25 mm
- Port sizeG3/8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM18×1.5
- CushionAdjustable, 29 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X25-10
The hard-anodized aluminum barrel keeps the build clean without external tie rods. A G3/8 port feeds the double-acting double-rod piston, while adjustable air cushions of 29 mm absorb end impacts.
The -10 suffix means an external stop screw lets you shorten the extend stroke on-site by up to 10 mm, dropping the usable forward travel from the 25 mm maximum down to 15 mm for fine position tuning without swapping the cylinder. The retract end remains fixed. This SKU lacks a magnet, so it cannot take a CMSE or DMSE sensor. Note that the cushion only decelerates; use an external rod lock or pilot-operated check valve if you need to hold a load on air loss.
Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X25-10 Technical Specifications
| Model | Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X25-10 |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 25 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | G3/8 |
| Rod thread | M18×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | 1962 N |
| Max (@1.0 MPa) | 286 kgf | |
JSIJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative).
Model Code: Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X25-10
| JSIJ | JIS-standard profile cylinder (adjustable-stroke type). |
|---|---|
| 63 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×25 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X25-10 Is Used
Short-Stroke Clamping
Tunes the final 15 to 25 mm clamping contact point on-site via the external adjuster to compensate for varying material thicknesses.
Transfer Stopper Gate
Acts as a compact JIS-profile stop gate that fits into tight conveyor frames, using the 10 mm window to dial in the exact stopping height.
Is the Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X25-10 the Right Cylinder?
The 10 mm adjustable window is ideal when you need to tune a short final position on-site or want one shared spare across slight stroke variants. Mounting options include FA, LB, TC, TCM1, and TCM2 brackets. Because this is a non-magnet SKU, you cannot fit position sensors; order the -S version if your circuit needs CMSE or DMSE switches. Even at this 25 mm stroke, ensure adequate guiding if the payload imposes side loads.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X25-10 FAQ
This 63 mm bore cylinder uses a G3/8 port and a 20 mm rod with an M18x1.5 thread.
The nominal stroke is 25 mm, which is the maximum extend travel. The external adjuster lets you shorten that forward stroke by up to 10 mm on-site, giving a usable extend range of 15 to 25 mm. The retract end is fixed, and this stop mechanism only sets the end position rather than locking the load.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X25-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.