Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X25-10S
The AirTAC JSIJ63~80 Adjustable Cylinder JSIJ63X25-10S is a genuine double acting, double rod, adjustable stroke JIS-standard air cylinder with a Ø63mm bore and 25mm stroke, G3/8 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
- BoreØ63 mm
- Stroke25 mm
- Port sizeG3/8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM18×1.5
- CushionAdjustable, 29 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X25-10S
The hard-anodized aluminium barrel keeps the frame clean while the G3/8 port feeds the 20 mm rod. A built-in magnet (-S) readies the body for CMSE or DMSE sensors.
The external adjuster lets you shorten the extend stroke on-site by up to 10 mm, so the usable travel is 15 to 25 mm without swapping the cylinder. The retract end stays fixed, and the stop screw sets the end position rather than locking the load.
Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X25-10S Technical Specifications
| Model | Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X25-10S |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 25 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | G3/8 |
| Rod thread | M18×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | 1962 N |
| Max (@1.0 MPa) | 286 kgf | |
JSIJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative).
Model Code: Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X25-10S
| JSIJ | JIS-standard profile cylinder (adjustable-stroke type). |
|---|---|
| 63 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×25 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Where the Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X25-10S Is Used
Clamp Position Trimming
Dial in the exact 15 to 25 mm clamp contact point on-site via the external stop screw without remachining the fixture.
Short-Stroke Sorting Gate
Fit a compact JIS profile diverter in a tight conveyor gap and use the magnet for immediate position feedback.
Press Fit Depth Control
Shorten the extend stroke by up to 10 mm to set a precise lower pressing limit for delicate seating tasks.
Is the Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X25-10S the Right Cylinder?
If 1559 N at 0.5 MPa is too much, step down to the 50 mm bore for 982 N; if you need more thrust, the 80 mm bore gives 2513 N. The 10 mm adjuster is perfect for sharing a spare across slightly different short-stroke variants and fine-tuning the end position on-site. Mounting options include FA, LB, TC, TCM1, and TCM2. The -S magnet accepts CMSE/DMSE switches. Even at 25 mm, always guide the load to prevent side-load wear.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X25-10S FAQ
At 0.5 MPa it pushes 1559 N and pulls 1402 N. At 0.7 MPa it pushes 2182 N and pulls 1962 N. The theoretical max is 318 kgf at 1.0 MPa. It uses a G3/8 port and a 20 mm rod with an M18x1.5 thread.
The nominal extend stroke is 25 mm. The external adjuster lets you shorten that extend travel by up to 10 mm on-site, giving a usable range of 15 to 25 mm. The retract end is fixed, and the adjuster sets the end position but does not lock the load.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC JSI Cylinders
Request a Quote for Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X25-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.