
The AirTAC JSIJ63~80 Adjustable Cylinder JSIJ63X450-30 is a genuine double acting, double rod, adjustable stroke JIS-standard air cylinder with a Ø63mm bore and 450mm stroke, G3/8 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
The external stop screw lets you trim the extend stroke on-site by up to 30 mm, giving a usable 420-450 mm window so you can fine-tune the end position without swapping the cylinder. Note this plain SKU lacks a magnet and cannot take a CMSE or DMSE sensor. The retract end remains fixed, and while the 29 mm adjustable air cushions decelerate the piston near the ends, they do not lock the load; use an external rod lock or pilot-operated check valve if you need to hold position against air loss.
| Model | Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X450-30 |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 450 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | G3/8 |
| Rod thread | M18×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | 1962 N |
| Max (@1.0 MPa) | 286 kgf | |
JSIJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative).
| JSIJ | JIS-standard profile cylinder (adjustable-stroke type). |
|---|---|
| 63 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×450 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Trim the 450 mm extend stroke by up to 30 mm on-site to perfectly strike a product push-off bar without repositioning the entire conveyor mount.
Dial in the exact stopping point for varying pallet depths on a packaging line, using the external adjuster to compensate for machine frame tolerances.
Fine-tune the clamping reach on a machining fixture by shorting the extend window, ensuring delicate parts are held securely without over-travel.
The 30 mm adjust window is a major advantage when you need to share one spare across several stroke variants or dial in a precise end position on the machine. You can mount it via FA, LB, TC, TCM1 or TCM2 brackets. Because this is a non-magnet version, you cannot fit CMSE or DMSE switches; choose an -S variant if you need position sensing. With a 450 mm stroke, always support the load with an external guide to prevent rod bending and side-load damage.
Quick checklist
It uses a G3/8 port, a 20 mm rod with an M18x1.5 thread, and has 29 mm adjustable air cushions at both ends.
The 450 mm nominal stroke is the maximum. The external stop screw lets you shorten the extend stroke by up to 30 mm on-site, yielding a usable 420-450 mm range. The retract end is fixed, and this adjustment sets the end position rather than acting as a load lock.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.