
The AirTAC JSIJ63~80 Adjustable Cylinder JSIJ63X700-100S is a genuine double acting, double rod, adjustable stroke JIS-standard air cylinder with a Ø63mm bore and 700mm stroke, G3/8 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
The external adjuster allows you to shorten the extend stroke by up to 100 mm, giving a usable range of 600 to 700 mm while the retract end remains fixed. Its extruded hard-anodized aluminum barrel omits tie rods entirely, making the body shorter and more compact than a same-bore ISO 15552 unit. The G3/8 port feeds a double-acting double-rod mechanism with a 20 mm piston rod and M18x1.5 thread.
Because the -S suffix includes a piston magnet, the side grooves accept CMSE or DMSE reed and electronic switches for precise positioning. The 29 mm adjustable air cushions at each end absorb kinetic energy to protect the end caps, though the stop screw and cushions only decelerate the piston; they do not lock the load. For vertical or suspended loads that must hold position on air loss, fit an external rod lock or pilot-operated check valve.
| Model | Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X700-100S |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 700 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | G3/8 |
| Rod thread | M18×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | 1962 N |
| Max (@1.0 MPa) | 286 kgf | |
JSIJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative).
| JSIJ | JIS-standard profile cylinder (adjustable-stroke type). |
|---|---|
| 63 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×700 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Fine-tune the 600 to 700 mm extend reach on-site to push parts onto parallel conveyor lanes without replacing the actuator.
Adjust the stop position by up to 100 mm to accommodate different pallet depths while using the built-in magnet for position confirmation.
Set the exact lower end position for light pressing tasks, relying on the 29 mm cushions to absorb the impact at the end of travel.
When sizing this actuator, stepping down to a 50 mm bore drops the 0.5 MPa push force to 982 N, while stepping up to an 80 mm bore raises it to 2513 N. The 63 mm bore sits in a strong middle ground for medium-duty handling. The adjustable stroke is ideal when you need to fine-tune the extend endpoint without swapping the cylinder, or when you want a shared spare across multiple stroke variants. Mounting options include Basic, FA, LB, TC, TCM1, and TCM2 brackets. The -S magnet enables CMSE/DMSE sensor feedback. Because the 700 mm stroke is relatively long, always support the load with an external guide rail to prevent rod bending and excessive side loading.
Quick checklist
The theoretical maximum force is 318 kgf at 1.0 MPa. This 63 mm bore model uses a G3/8 air port, a 20 mm rod, and an M18x1.5 rod thread.
The nominal 700 mm stroke is the maximum extend length. An external stop screw lets you shorten the extend stroke by up to 100 mm on-site, yielding a usable range of 600 to 700 mm. The retract end is fixed, and this stop mechanism only sets the end position; it does not lock or hold the load.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.