
The AirTAC JSIJ63~80 Adjustable Cylinder JSIJ63X700-75 is a genuine double acting, double rod, adjustable stroke JIS-standard air cylinder with a Ø63mm bore and 700mm stroke, G3/8 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
The hard-anodized aluminium barrel keeps the overall body shorter and more compact than a same-bore ISO 15552 unit. A G3/8 port supplies the air, while the external stop screw lets you trim the extend stroke by up to 75 mm without swapping the actuator.
The nominal 700 mm stroke represents the maximum travel, yielding a usable extend range of 625 to 700 mm, and the retract end remains fixed. Because this specific SKU lacks the -S magnet option, it cannot take a CMSE or DMSE sensor. Note that the adjustable air cushions only decelerate the piston near the ends; they do not hold the load. To prevent drift on air loss, fit an external rod lock or a pilot-operated check valve.
| Model | Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X700-75 |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 700 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | G3/8 |
| Rod thread | M18×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | 1962 N |
| Max (@1.0 MPa) | 286 kgf | |
JSIJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative).
| JSIJ | JIS-standard profile cylinder (adjustable-stroke type). |
|---|---|
| 63 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×700 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Fine-tune the extend end point within the 75 mm window during setup to hit a precise 625 mm clamping depth without machining new spacers.
Alter the extend stroke on site to accommodate varying pallet widths, using the external stop screw to set the exact 650 mm stopping distance.
Lift a 79 kg payload vertically using the 0.5 MPa push force, adjusting the final lower position by up to 75 mm for delicate placement.
The 75 mm adjust window is ideal for sharing one spare actuator across several stroke variants or fine-tuning a tooling position during machine commissioning. You can mount it using the FA, LB, TC, TCM1, or TCM2 brackets. Since the 700 mm stroke is quite long, always use an external guide rail to prevent rod bending and side-load damage. Remember that this no-magnet SKU cannot support position sensing.
Quick checklist
This 63 mm bore cylinder pushes with 1559 N and pulls with 1402 N at 0.5 MPa. At 0.7 MPa, push is 2182 N and pull is 1962 N. The theoretical maximum force is 318 kgf at 1.0 MPa. It uses a G3/8 air port and features a 29 mm adjustable air cushion at each end.
The nominal 700 mm stroke is the maximum travel. The external adjuster lets you shorten the extend stroke on site by up to 75 mm, giving a usable extend range of 625 to 700 mm. The retract end is fixed, and this stop mechanism only sets the end position—it does not lock the load.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.