
The AirTAC JSIJ63~80 Adjustable Cylinder JSIJ63X75-10S is a genuine double acting, double rod, adjustable stroke JIS-standard air cylinder with a Ø63mm bore and 75mm stroke, G3/8 air ports and adjustable end cushioning. Its no-tie-rod, hard-anodized profile barrel is more compact than an ISO 15552 cylinder of the same bore — a space-saver on tight machines.
A built-in piston magnet supports CMSE and DMSE switches that drop directly into the side grooves for precise position detection. The G3/8 porting feeds the double-acting double rod, while adjustable air cushions of 29 mm at each end absorb end-of-stroke impact.
The external adjuster lets you shorten the extend stroke on site by up to 10 mm, yielding a usable range of 65 to 75 mm without changing the cylinder itself. This on-site tuning is ideal for dialing in a specific end position, and it lets you stock one unit for several stroke variants.
| Model | Airtac JSIJ63~80 Adjustable Cylinder JSIJ63X75-10S |
|---|---|
| Series | JSI JIS-standard profile cylinder |
| Bore size | Ø63 mm |
| Stroke | 75 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | G3/8 |
| Rod thread | M18×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 29 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC JSI (JIS standard) datasheet. Confirm against the product label before installation. Thread options: PT (blank) / G. Barrel: hard-anodized aluminum profile (no tie rods).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | 1962 N |
| Max (@1.0 MPa) | 286 kgf | |
JSIJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative).
| JSIJ | JIS-standard profile cylinder (adjustable-stroke type). |
|---|---|
| 63 | Bore size in mm (32 / 40 / 50 / 63 / 80 / 100 / 125). |
| ×75 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensors. |
JSI-family variants: JSI (double acting), JSID (double rod), JSIJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / TCM1 / TCM2. Thread PT (blank) / G.
Dial in the exact clamping depth on a fixture by shortening the extend stroke up to 10 mm on site, ensuring perfect part contact without redesigning the tooling.
Adjust the stopper block position on a conveyor line by trimming the extend stroke from 75 mm down to 65 mm to accommodate varying product sizes.
Keep one cylinder as a spare for multiple machines by using the external adjuster to match the specific 65 to 75 mm extend stroke required by each station.
The 63 mm bore sits in a strong middle ground, and the 10 mm adjustable window means you can fine-tune the extend end position on site rather than machining custom spacers. You can mount it via FA, LB, TC, TCM1, or TCM2 brackets. The -S suffix indicates the magnet is present for CMSE/DMSE sensors. For any stroke over 300 mm, always use a guide rail to prevent side-load damage. Remember that the external stop sets the end position but does not lock the load; use an external rod lock or pilot-operated check valve if you need to hold a load against air loss.
Quick checklist
At 0.7 MPa the push is 2182 N and the pull is 1962 N. The theoretical maximum force is 318 kgf at 1.0 MPa. It uses a G3/8 port and a 20 mm rod with an M18x1.5 thread.
The 75 mm nominal stroke is the maximum. The external adjuster lets you shorten the extend stroke by up to 10 mm on site, giving a usable extend range of 65 to 75 mm. The retract end is fixed. This mechanism only sets the end position and does not hold the load without live air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.