Airtac MAC Stainless Steel Mini Air Cylinder MAC63X10SCA
The AirTAC Airtac MAC Stainless Steel Mini Air Cylinder MAC63X10SCA is a genuine double acting + cushion standard round-body mini air cylinder with a Ø63mm bore and 10mm stroke, 1/4" air ports and a stainless-steel barrel with a hard-chrome-plated rod for reliable, mildly corrosion-resistant service. A variable air cushion at both ends lets you tune end-of-stroke deceleration on site.
- BoreØ63 mm
- Stroke10 mm
- Port size1/4"
- Acting typeDouble acting + cushion
- Rod threadM14×1.5
- CushionVariable air cushion, both ends
About the Airtac MAC Stainless Steel Mini Air Cylinder MAC63X10SCA
Short travel, serious muscle: a 10 mm stroke on a 63 mm cushioned piston gives the MAC63X10SCA 1557.9 N of push and 1457.4 N of pull at 0.5 MPa - enough to clamp, mark or prove-part on tight machine faces through PT 1/4" ports. The cylinder is double acting with a variable cushion at each end, runs on 0.15-1.0 MPa (22-145 psi) and cycles at 30-800 mm/s.
Inside is a stainless-steel barrel with rolled-in cover construction and a 16 mm hard-chrome rod, so frequent washdown or damp workshop air will not flake a coating the way it does on painted minis. For real-world sizing, budget roughly six tenths of the rating - near 935 N of useful force at 0.5 MPa - rather than the full thrust, a figure that suits heavy clamping jigs. The CA pivot back cover swings on a pin for linkage-style clamps, and the built-in magnet means CMSG, DMSG or EMSG switches work straight out of the box.
Airtac MAC Stainless Steel Mini Air Cylinder MAC63X10SCA Technical Specifications
| Model | Airtac MAC Stainless Steel Mini Air Cylinder MAC63X10SCA |
|---|---|
| Series | MAC mini cylinder |
| Bore size | Ø63 mm |
| Stroke | 10 mm |
| Acting type | Double acting + cushion |
| Port size | 1/4" |
| Rod thread | M14×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MA-series datasheet. Barrel: stainless-steel tube (round-body, riveted rolling-packed construction); piston rod: carbon steel with 20µm hard-chrome plating; covers: aluminium alloy. Thread options: PT (blank) / G / NPT. Every MA-series cylinder ships with a built-in magnet for CMSG / DMSG / EMSG position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1458 N |
| 0.7 MPa | 2182 N | 2041 N |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MAC Stainless Steel Mini Air Cylinder MAC63X10SCA
| MAC | Standard round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 63 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| -S | Built-in magnet for CMSG / DMSG / EMSG sensors (standard on MA series). |
| CA / U / CM | Back-cover type: CA pivot, U flat-end, CM round-end. |
MA-family variants: MA / MAC (double acting ±cushion), MSA / MTA (single acting push / pull), MAD / MACD (double rod ±cushion), MAJ / MACJ (adjustable stroke ±cushion), MAR (cushioned with integrated F/U mount). Mounting accessories: FA flange, LB foot, SDB pivot; plus I and Y knuckles. Thread PT (blank) / G / NPT.
Where the Airtac MAC Stainless Steel Mini Air Cylinder MAC63X10SCA Is Used
Weld fixture clamp
Swings a hook clamp onto tube assemblies at a robotic weld cell; the practical working force of about 935 N at 0.5 MPa holds parts against torch distortion.
Sample press in a lab rig
Presses test coupons into a fixture with a controlled 10 mm push; the short stroke and cushion stop any over-travel from damaging delicate specimens.
Carton hold-down
Pins the top flap of a carton while a taping head finishes the seam, then retracts instantly so the next box on the infeed is not delayed.
Is the Airtac MAC Stainless Steel Mini Air Cylinder MAC63X10SCA the Right Cylinder?
One step smaller, the 40 mm bore still gives 628.3 N push at 0.5 MPa if clamp force is modest; 63 mm is the top of this series, so 2181.0 N at 0.7 MPa is your ceiling. The 10 mm stroke keeps rod bending nearly a non-issue, but check the pin load on the CA pivot eye against your linkage ratio. Because the rod moves freely when the valve centres or air fails, add a rod lock or pilot check valve whenever a clamp must stay closed on pressure loss. FA flange, LB foot and SDB options cover fixed installations.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) is standard for sensors
- ✓ Back cover (CA/U/CM) & mount (FA/LB/SDB)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check On first run, back off the cushion screws and release gradually.
- check Installation by qualified personnel per AirTAC docs.
Airtac MAC Stainless Steel Mini Air Cylinder MAC63X10SCA FAQ
Push is 1557.9 N and pull 1457.4 N at 0.5 MPa; at 0.7 MPa expect 2181.0 N push and 2040.3 N pull, with 317.7 kgf the theoretical maximum at 1.0 MPa. Pressure range is 0.15-1.0 MPa (22-145 psi).
It provides a machined pivot eye so the cylinder swings on a pin inside a linkage or toggle clamp without extra clevis hardware; for fixed bases choose the FA flange, LB foot or SDB bracket instead.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MAC Stainless Steel Mini Air Cylinder MAC63X10SCA
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.