This model is discontinued
AirTAC has phased out the MAL series. You can still order this code here: we ship the direct replacement MBL20X105CA, with the same bore, stroke, output force, port and mounting, so it fits the same application. The MBL replacement upgrades to a riveted rolling-packed body and the current CMSG / DMSG / EMSG sensor switches (the MAL used CS1-M / DS1-M).
Airtac MAL20 Aluminum Alloy Mini Cylinder MAL20X105CA
The AirTAC MAL20 Aluminum Alloy Mini Cylinder MAL20X105CA is a double-acting aluminum-barrel mini round cylinder with a Ø20mm bore and 105mm stroke, G1/8 air ports and a fixed rubber bumper. This model is discontinued — the direct replacement is the MBL20X105CA, which matches its bore, stroke, force and mounting.
- BoreØ20 mm
- Stroke105 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM8×1.25
- StatusDiscontinued → MBL20X105CA
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MAL20 Aluminum Alloy Mini Cylinder MAL20X105CA
The AirTAC MAL20X105CA is a discontinued compact double-acting aluminum mini round cylinder. Delivering 157 N of push force at 0.5 MPa, it features a 20 mm bore and a 105 mm stroke. The direct replacement is the MBL20X105CA, which matches the bore, stroke, output force, G1/8 port, and CA pivot mounting. The legacy MAL uses threaded front and back covers, whereas the current MBL features a riveted rolling-packed body for equally robust performance.
This specific SKU includes a CA pivot (clevis) back cover that swings on a pin to accommodate arcing loads, and because it lacks the -S code, it cannot accept a position sensor. Internally, a heterogeneous two-way seal retains grease, and the 8 mm carbon-steel rod features 20 um hard-chrome plating for wear resistance. End-of-stroke deceleration relies on a fixed rubber bumper rather than an adjustable cushion.
Airtac MAL20 Aluminum Alloy Mini Cylinder MAL20X105CA Technical Specifications
| Model | Airtac MAL20 Aluminum Alloy Mini Cylinder MAL20X105CA |
|---|---|
| Series | MAL aluminum-barrel mini round cylinder (discontinued) |
| Replacement | MBL20X105CA |
| Bore size | Ø20 mm |
| Stroke | 105 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MAL datasheet (now discontinued). The MBL20X105CA carries the same ratings. Confirm against the product label before installation. Thread options: PT / G / NPT.
Theoretical Output Force (Ø20mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 157 N | 132 N |
| 0.7 MPa | 220 N | — |
| Max (@1.0 MPa) | 32 kgf | |
The MBL20X105CA produces the same force from the same bore. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac MAL20 Aluminum Alloy Mini Cylinder MAL20X105CA
| MAL | Aluminum-barrel mini round cylinder, double acting (discontinued). |
|---|---|
| 20 | Bore size in mm (20/25/32/40). |
| ×105 | Stroke length in mm. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBL uses CMSG/DMSG/EMSG). |
| CA / U / CM | Back cover: CA pivot, U flat-end or CM round-end. |
Replacement mapping: MAL → MBL, MSAL → MSBL, MTAL → MTBL, MALD → MBLD, MALJ → MBLJ.
Where the Airtac MAL20 Aluminum Alloy Mini Cylinder MAL20X105CA Is Used
Textile Loom Guide Arms
Drives lightweight guide arms on textile looms, where the 157 N push force at 0.5 MPa is sufficient for thread tensioning and the CA clevis absorbs pivot arc.
PCB Shuttle Diverters
Actuates small shuttle diverters on PCB conveyor lines, utilizing the 105 mm stroke to index boards between inspection stations without overwhelming the assembly.
Packaging Flap Folders
Folds small cardboard flaps on mini-packaging lines, where the compact 20 mm bore fits tight frame gaps and the fixed rubber bumper softens the retraction stop.
Replacing the Airtac MAL20 Aluminum Alloy Mini Cylinder MAL20X105CA with MBL20X105CA
To replace the MAL20X105CA, order the MBL20X105CA. Verify your setup accommodates the PT tapered port thread, the M8x1.25 rod-end thread, and the CA pivot clevis. If your machine requires end-position feedback, note that this non-magnetized SKU cannot support a sensor; you must specify an MBL20X105CAS instead, which shifts you to the modern CMSG, DMSG, or EMSG switch family rather than the legacy CS1-M or DS1-M. The fixed rubber bumper cannot be adjusted; if your application requires precise end-of-stroke damping, step up to the MBLC variant on the current line.
For sizing flexibility, stepping down to the next available bore is not an option as 20 mm is the smallest in this series. Stepping up to the 25 mm bore yields 245 N of push force at 0.5 MPa. A plain MBL does not hold its position or load when air pressure is lost; the rod will drift. For a held load, install an external rod lock or a pilot-operated check valve. At 105 mm stroke, side-load tolerance is moderate due to the 8 mm rod; ensure the CA clevis is free to articulate to prevent rod bending.
Upgrade checklist
- ✓ Order the MBL20X105CA (same bore/stroke/force)
- ✓ Same G1/8 port and mounting accessories
- ✓ Sensor: swap CS1-M/DS1-M → CMSG/DMSG/EMSG
- ✓ Need a cushion? use MBLC (adjustable air cushion)
- ✓ Confirm back cover (CA / U) and thread (PT/NPT/G)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.1 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Front/rear covers are threaded — not intended for field disassembly.
- check Use the correct mounting accessory (LB / FA / SDB) and back cover (CA / U / CM).
- check For new builds, specify the MBL20X105CA instead of this discontinued model.
Airtac MAL20 Aluminum Alloy Mini Cylinder MAL20X105CA FAQ
Yes, the MAL20X105CA is discontinued. The direct replacement is the MBL20X105CA, offering the same 20 mm bore, 105 mm stroke, G1/8 port, and CA pivot mounting. The MBL upgrades the body to a riveted rolling-packed structure while maintaining the original force profile.
At 0.5 MPa, the push force is 157 N and the pull force is 132 N. At 0.7 MPa, the push force is 220 N, with a theoretical maximum of 32 kgf at 1.0 MPa. Because this specific SKU lacks the -S magnet code, it cannot accept CS1-M or DS1-M position sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
Direct Upgrade
The MBL20X105CA replaces this model 1:1.
Fast Dispatch
MBL replacements are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Recommended AirTAC MBL Replacements
Request a Quote (Airtac MAL20 Aluminum Alloy Mini Cylinder MAL20X105CA → MBL20X105CA)
Tell us the quantity and destination — we quote the direct MBL20X105CA replacement with price, stock and lead time, usually within 7-8 hours.