This model is discontinued
AirTAC has phased out the MAL series. You can still order this code here: we ship the direct replacement MBL20X700CA, with the same bore, stroke, output force, port and mounting, so it fits the same application. The MBL replacement upgrades to a riveted rolling-packed body and the current CMSG / DMSG / EMSG sensor switches (the MAL used CS1-M / DS1-M).
Airtac MAL20 Aluminum Alloy Mini Cylinder MAL20X700CA
The AirTAC MAL20 Aluminum Alloy Mini Cylinder MAL20X700CA is a double-acting aluminum-barrel mini round cylinder with a Ø20mm bore and 700mm stroke, G1/8 air ports and a fixed rubber bumper. This model is discontinued — the direct replacement is the MBL20X700CA, which matches its bore, stroke, force and mounting.
- BoreØ20 mm
- Stroke700 mm
- Port sizeG1/8
- Acting typeDouble acting
- Rod threadM8×1.25
- StatusDiscontinued → MBL20X700CA
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MAL20 Aluminum Alloy Mini Cylinder MAL20X700CA
The AirTAC MAL20X700CA is a discontinued double-acting aluminum mini round cylinder with a 20mm bore and a 700mm stroke. Because 700mm exceeds the 500mm standard limit, this is a made-to-order non-standard stroke. It delivers 157N push and 132N pull at 0.5MPa. The direct replacement is the MBL20X700CA, matching the force, G1/8 port, and CA pivot mounting.
This legacy MAL features threaded front and back covers, whereas the modern MBL utilizes a riveted rolling-packed body. Without an -S magnet, this specific SKU cannot support a position sensor. Furthermore, driving an 8mm rod over 700mm demands careful alignment; the self-lubricating front-cover bearing guide and heterogeneous two-way grease-retaining seal help manage friction, but external guidance is essential to prevent rod bending.
Airtac MAL20 Aluminum Alloy Mini Cylinder MAL20X700CA Technical Specifications
| Model | Airtac MAL20 Aluminum Alloy Mini Cylinder MAL20X700CA |
|---|---|
| Series | MAL aluminum-barrel mini round cylinder (discontinued) |
| Replacement | MBL20X700CA |
| Bore size | Ø20 mm |
| Stroke | 700 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MAL datasheet (now discontinued). The MBL20X700CA carries the same ratings. Confirm against the product label before installation. Thread options: PT / G / NPT.
Theoretical Output Force (Ø20mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 157 N | 132 N |
| 0.7 MPa | 220 N | — |
| Max (@1.0 MPa) | 32 kgf | |
The MBL20X700CA produces the same force from the same bore. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac MAL20 Aluminum Alloy Mini Cylinder MAL20X700CA
| MAL | Aluminum-barrel mini round cylinder, double acting (discontinued). |
|---|---|
| 20 | Bore size in mm (20/25/32/40). |
| ×700 | Stroke length in mm. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBL uses CMSG/DMSG/EMSG). |
| CA / U / CM | Back cover: CA pivot, U flat-end or CM round-end. |
Replacement mapping: MAL → MBL, MSAL → MSBL, MTAL → MTBL, MALD → MBLD, MALJ → MBLJ.
Where the Airtac MAL20 Aluminum Alloy Mini Cylinder MAL20X700CA Is Used
Textile Loom Guide
Actuates a yarn guide arm over a 700mm span, where the 157N push force at 0.5MPa is sufficient for the lightweight mechanism and the CA pivot absorbs pivoting inertia.
Packaging Pusher
Transfers light cardboard cartons across a wide belt, using the 132N pull force to retract the 8mm rod rapidly without over-stressing the packaging flap.
Drawer Extraction Arm
Pulls a loaded parts drawer out of a tight cabinet, relying on the self-lubricating bearing guide to prevent binding over the extended 700mm travel.
Replacing the Airtac MAL20 Aluminum Alloy Mini Cylinder MAL20X700CA with MBL20X700CA
To replace the MAL20X700CA, order the MBL20X700CA. Verify your PT thread port, CA pivot back cover, and 700mm stroke. If you need a position sensor, you must upgrade to an MBL20X700SCA, which uses the modern CMSG/DMSG/EMSG switches rather than the legacy CS1-M/DS1-M. If 157N at 0.5MPa is too much force, step down to the 12mm bore (confirm force from datasheet); if you need more force, step up to the 25mm bore (245N at 0.5MPa).
At 700mm, the 8mm carbon-steel rod with 20um hard-chrome plating has low side-load tolerance. Use the CA pivot clevis to absorb arcing loads, or add an external guide rail. The fixed rubber bumper softens end-of-stroke impact but does not lock the rod; if air is lost, the load drifts. For adjustable cushioning, switch to the current MBLC series.
Upgrade checklist
- ✓ Order the MBL20X700CA (same bore/stroke/force)
- ✓ Same G1/8 port and mounting accessories
- ✓ Sensor: swap CS1-M/DS1-M → CMSG/DMSG/EMSG
- ✓ Need a cushion? use MBLC (adjustable air cushion)
- ✓ Confirm back cover (CA / U) and thread (PT/NPT/G)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.1 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Front/rear covers are threaded — not intended for field disassembly.
- check Use the correct mounting accessory (LB / FA / SDB) and back cover (CA / U / CM).
- check For new builds, specify the MBL20X700CA instead of this discontinued model.
Airtac MAL20 Aluminum Alloy Mini Cylinder MAL20X700CA FAQ
Yes, the AirTAC MAL20X700CA is discontinued. The direct replacement is the MBL20X700CA, offering the same 20mm bore, 700mm stroke, 157N push force, G1/8 port, and CA pivot mounting.
The 20mm bore generates 157N push and 132N pull at 0.5MPa, 220N push at 0.7MPa, and a maximum of 32kgf at 1.0MPa. The fixed rubber bumper only softens end-of-stroke impact; it does not hold the load if air pressure drops, so an external rod lock is needed for holding.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
Direct Upgrade
The MBL20X700CA replaces this model 1:1.
Fast Dispatch
MBL replacements are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Recommended AirTAC MBL Replacements
Request a Quote (Airtac MAL20 Aluminum Alloy Mini Cylinder MAL20X700CA → MBL20X700CA)
Tell us the quantity and destination — we quote the direct MBL20X700CA replacement with price, stock and lead time, usually within 7-8 hours.