Airtac MBLD Dual Axis Type Mini Cylinder MBLD40X500
The AirTAC MBLD Dual Axis Type Mini Cylinder MBLD40X500 is a genuine double-acting double-rod aluminum-barrel mini cylinder with a Ø40mm bore and 500mm stroke. A rod exits both end covers, so extend and retract force are EQUAL — about 528 N each way at 0.5 MPa. Fixed rubber bumper.
- BoreØ40 mm
- Stroke500 mm
- Port sizeG1/4
- Acting typeDouble acting, double rod
- Rod threadM12×1.25
- CushionFixed rubber bumper
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MBLD Dual Axis Type Mini Cylinder MBLD40X500
The AirTAC MBLD40X500 is a double-acting, double-rod aluminum mini cylinder featuring a 40mm bore and a 500mm stroke. Because a carbon-steel rod with 20µm hard-chrome plating exits both end covers, the effective piston area is identical on extend and retract. This yields equal force and speed in both directions, generating 528N at 0.5MPa and 739N at 0.7MPa. The 500mm stroke is a made-to-order non-standard length for this bore, extending to the absolute maximum travel limit before external guidance becomes critical.
This configuration uses a G1/4 port and an M12x1.25 rod-end thread. It features a riveted rolling-packed aluminum barrel and a fixed rubber bumper to soften end-of-stroke impact. This specific SKU is built without a magnet, so it cannot support CMSG, DMSG, or EMSG position sensors. The overall length equals the base body length plus twice the stroke, meaning the rear rod protrudes significantly and requires dedicated machine clearance.
Airtac MBLD Dual Axis Type Mini Cylinder MBLD40X500 Technical Specifications
| Model | Airtac MBLD Dual Axis Type Mini Cylinder MBLD40X500 |
|---|---|
| Series | MBL aluminum-barrel mini round cylinder (double rod) |
| Bore size | Ø40 mm |
| Stroke | 500 mm |
| Acting type | Double acting, double rod |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 500 mm |
Double-rod overall length = A + 2 × stroke — leave clearance for the rear rod. MBLD/MBLCD mounting is Basic / FA / LB only (no SDB, no back-cover code). Thread options: PT / G / NPT.
Output Force (Ø40mm, equal both ways)
| Pressure | Extend & retract force |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod on both piston faces makes the annulus area equal, so extend and retract force (and speed) are the same. Actual usable force is lower due to friction.
Model Code: Airtac MBLD Dual Axis Type Mini Cylinder MBLD40X500
| MBLD | MBLD aluminum-barrel double-rod mini cylinder. |
|---|---|
| 40 | Bore size in mm. |
| ×500 | Stroke length in mm. |
| S | Optional built-in magnet for a CMSG/DMSG/EMSG sensor switch. |
| FA / LB | Mounting: FA flange or LB foot (no SDB on double-rod). |
Related: MBLCD (double rod, adjustable cushion), MBLC (single rod + cushion), MBL (single rod).
Where the Airtac MBLD Dual Axis Type Mini Cylinder MBLD40X500 Is Used
Long-Travel Stretch Web Splicer
Drives a dual-sided splicing jaw on a film converting line, using the 500mm stroke to fully open the mechanism while the rear rod actuates a tensioning flag at 528N.
Reciprocating Shuttle Conveyor
Indexes a pallet transfer carriage between two machining stations, leveraging the equal extend and retract speed to maintain a consistent 30-800mm/s cycle rhythm.
Textile Beam Tensioner
Applies 739N of constant opposing force at 0.7MPa on a weaving loom, using the twin rods to keep the warp beam guided against rotation without a separate guide rod.
Is the Airtac MBLD Dual Axis Type Mini Cylinder MBLD40X500 the Right Cylinder?
When sizing this cylinder, consider stepping down to the 32mm bore (generating 346N at 0.5MPa) for lighter loads, or stepping up to the 50mm bore (providing 881N at 0.5MPa) for heavier thrust requirements. At 500mm of travel on a 16mm rod, side-load forces are highly amplified; an external linear guide is strictly required to prevent rod bending and premature seal wear.
Unlike the single-rod MBL which offers higher forward thrust, this MBLD provides balanced dual-side actuation. If your application needs adjustable pneumatic cushioning rather than the fixed rubber bumper found here, select the MBLCD variant. Mounting is limited to Basic, FA flange, or LB foot brackets; there is no SDB pivot or back-cover option. This SKU uses PT tapered thread and lacks the -S magnet code, meaning no sensor can be fitted. Replacement requires matching the 40mm bore, 500mm stroke, G1/4 port, PT thread, and double-rod layout.
Quick checklist
- ✓ Equal force both ways at your pressure
- ✓ Rear-rod clearance (length = A + 2 × stroke)
- ✓ Mounting: Basic / FA / LB only
- ✓ Magnet (S) for sensors?
- ✓ Side load — add a guide on long strokes
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Leave clearance for the rear rod (length = A + 2 × stroke).
- check Avoid side load; add an external guide on long strokes.
- check Mounting: Basic / FA flange / LB foot (no SDB, no back-cover code).
- check Installation by qualified personnel per AirTAC docs.
Airtac MBLD Dual Axis Type Mini Cylinder MBLD40X500 FAQ
Force is equal in both directions because the double-rod design creates identical annulus areas. It provides 528N at 0.5MPa and 739N at 0.7MPa. The maximum theoretical force is 108kgf (approx 1059N) at 1.0MPa.
No. This specific SKU lacks the -S code, meaning no internal magnet is fitted and it cannot trigger CMSG reed or DMSG/EMSG electronic sensors. You must use external limit switches for position detection.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC Double-Rod Cylinders
Request a Quote for Airtac MBLD Dual Axis Type Mini Cylinder MBLD40X500
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.