Airtac MICJ Adjustable Mini Cylinder MICJ16X100-10S
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X100-10S is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 100mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke100 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X100-10S
Dial in a precise forward stop on-site with this stainless-steel round-body mini cylinder, which trims the extend stroke by up to 10 mm via an external screw. As a double-acting actuator, it pairs that settable end-position with an adjustable air cushion at both ends to soak up high-speed shock, letting you control both the location and the impact of the stop.
The stainless construction resists mild corrosion and washdown environments. Because this SKU includes the -S magnet, it supports CMSG, DMSG, and EMSG position switches.
Airtac MICJ Adjustable Mini Cylinder MICJ16X100-10S Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X100-10S |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 100 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X100-10S
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X100-10S Is Used
Light Divert Stop
Acts as an adjustable stop gate for small packages on a conveyor, using the built-in magnet to confirm gate extension and the cushion to absorb high-speed impacts.
Film Feed Tensioning
Sets an exact forward reach on a packaging line to maintain film tension, relying on the stainless barrel for washdown resistance and the adjustable stop for fine-tuning.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X100-10S the Right Cylinder?
When sizing this 16 mm bore actuator, note that stepping down means moving to an MIJ bumper-only variant, as smaller cushions are not offered. If you need more force, the next size up is the 20 mm bore, which raises push force at 0.5 MPa to 157 N. Choose this model when you need fast, settable-position moves where the 10 mm extend trim and dual needle cushions prevent harsh end-strikes.
The external stop screw sets the forward end position but is not a mid-stroke lock; the cylinder will drift on air loss, so add an external rod lock or pilot check valve to hold a suspended load. For mounting, use LB foot, FA flange, or TC trunnion brackets (SDB pivot-block is not available on this adjustable variant), and rely on the internal magnet for sensor feedback.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X100-10S FAQ
This 16 mm bore cylinder features an M5×0.8 port and a 6 mm rod.
An external screw shortens the extend stroke by up to 10 mm, and a needle valve adjusts the air cushion at both ends to decelerate the piston near the stroke ends. The cushion only decelerates and does not lock; the piston drifts on air loss, so use an external rod lock for holding. The -S magnet enables CMSG, DMSG, and EMSG sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X100-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.