Airtac MICJ Adjustable Mini Cylinder MICJ16X160-75
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X160-75 is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 160mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke160 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X160-75
Trim the forward stop by up to 75 mm on site without swapping hardware using this AirTAC adjustable-stroke mini cylinder. The external screw sets the extend end position anywhere from 85 mm up to the full 160 mm, while the needle-set air cushions at both ends soak up high-speed shock.
Built with a stainless-steel round barrel and piston rod, the riveted construction resists mild corrosion and washdown environments. It uses the ISO 6432 mounting interface for standard mini brackets and features an M5×0.8 port. Because this specific SKU lacks the -S magnet option, it cannot accept CMSG, DMSG, or EMSG sensors.
Airtac MICJ Adjustable Mini Cylinder MICJ16X160-75 Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X160-75 |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 160 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X160-75
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×160 | Stroke length in mm. |
| -75 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X160-75 Is Used
Custom Length Ejection
Dial in the extend stroke from 85 to 160 mm to push parts of varying widths out of a machining center without retooling the actuator setup.
High-Speed Stop Trimming
Use the needle-set air cushions to absorb impact at the extend end while fine-tuning the 75 mm adjustment window for rapid, precise positioning.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X160-75 the Right Cylinder?
The 75 mm extend adjuster and dual air cushions are ideal for high-speed moves where you must dial in a precise forward stop on the fly.
Remember that the stop screw and cushions only decelerate the piston near the end of travel; they do not lock or hold the load mid-stroke. If air pressure drops, the rod will drift, so add an external pilot check valve for suspended loads. Mount using LB foot, FA flange, or TC trunnion brackets, as the SDB pivot block is not offered on this adjustable variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X160-75 FAQ
This 16 mm bore cylinder uses an M5×0.8 port.
An external screw shortens the extend stroke by up to 75 mm, while needle valves adjust the air cushions at both ends to absorb high-speed shock. The cushions only decelerate the piston; they do not lock or hold the load on air loss. This SKU also lacks a magnet, so it cannot take position sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X160-75
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.