Airtac MICJ Adjustable Mini Cylinder MICJ16X200-30S
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X200-30S is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 200mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke200 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X200-30S
Trim the forward stop by up to 30 mm on site without swapping hardware: the MICJ16X200-30S uses an external screw to shorten the extend end position from 200 mm down to 170 mm, while the retract stroke remains full. This double-acting, round-body stainless-steel mini cylinder pairs that settable extend position with a needle-adjustable air cushion at both ends, soaking up high-speed shock at the 30-800 mm/s operating range.
Built with a corrosion-resistant stainless barrel and Ø6 mm rod (M6x1.0 male thread), it conforms to the ISO 6432 mounting interface for straightforward bracket drops. The -S suffix means a piston magnet is built in for CMSG, DMSG or EMSG position sensing.
Airtac MICJ Adjustable Mini Cylinder MICJ16X200-30S Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X200-30S |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 200 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X200-30S
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -30 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X200-30S Is Used
Light-Part Ejection
Dial in the 170-200 mm extend stop to eject light molded parts precisely, using the dual air cushions to absorb the impact of high-speed 60 N working-load cycles.
Sensor-Checked Sorting
Use the built-in -S magnet with DMSG switches to confirm retraction, adjusting the extend end by up to 30 mm to sort lightweight widgets without crushing them.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X200-30S the Right Cylinder?
Size this 100.5 N (0.5 MPa) unit against the next bore up, the Ø20, which pushes 157 N, or drop to an MIJ bumper-only cylinder if your force needs are lower. The 30 mm extend adjuster plus dual air cushions shine in fast set-position moves where you need to dial in a precise forward stop and control end-impact without external shock absorbers. The stop screw sets the end position but is not a mid-stroke lock; the air cushion only decelerates near the stroke end. If the load must hold on air loss, add an external rod lock or pilot check valve.
Mount via LB foot, FA flange or TC trunnion (SDB pivot-block is not available on this adjustable variant), with back covers CA, U, R or CM. The -S magnet enables CMSG/DMSG/EMSG switches; a SKU without S cannot take a sensor.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X200-30S FAQ
The theoretical maximum force is 20.5 kgf at 1.0 MPa.
An external screw shortens the extend stroke by up to 30 mm (retract is unaffected), and a needle valve adjusts the air cushion at both ends to decelerate high-speed moves. The cushion is not a brake, and the piston will drift on air loss; use an external rod lock for holding. The -S suffix enables CMSG/DMSG/EMSG sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X200-30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.