Airtac MICJ Adjustable Mini Cylinder MICJ16X200-75S
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X200-75S is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 200mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke200 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X200-75S
Dial in a precise forward stop on-site with the AirTAC MICJ16X200-75S, a stainless-steel round-body mini cylinder that shortens its extend stroke by up to 75 mm via an external screw. The built-in magnet (-S) supports CMSG, DMSG, and EMSG sensors for position tracking.
This double-acting actuator pairs its adjustable extend end with a needle-set variable air cushion at both ends to soak up high-speed shock. The stainless barrel and rod resist mild corrosion and washdown. Conforming to the ISO 6432 mounting interface, it drops into standard mini brackets while giving you total control over the end position and impact deceleration.
Airtac MICJ Adjustable Mini Cylinder MICJ16X200-75S Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X200-75S |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 200 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X200-75S
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -75 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X200-75S Is Used
Carton Flap Folding
Dial in the exact forward position to fold light packaging flaps without crushing the material, relying on the stainless rod for washdown resistance.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X200-75S the Right Cylinder?
The 75 mm extend trim and dual air cushions shine in fast set-position moves where you must tune the forward stop without swapping hardware. For mounting, use LB foot, FA flange, or TC trunnion (the SDB pivot-block is not offered on this adjustable variant).
The external screw sets the end position but is not a mid-stroke lock. The air cushion only decelerates the piston near the stroke end; it will not hold a load. If air loss occurs, the piston drifts, so fit an external rod lock or pilot-operated check valve for suspended loads. The -S magnet enables position sensing.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X200-75S FAQ
It uses an M5×0.8 port. At 0.5 MPa it pushes 100.5 N and pulls 86.4 N. At 0.7 MPa it pushes 140.7 N and pulls 120.9 N. The theoretical maximum force is 20.5 kgf at 1.0 MPa.
An external screw shortens the extend stroke by up to 75 mm, while needle valves tune the variable air cushion at both ends to decelerate high-speed moves. The -S magnet enables CMSG/DMSG/EMSG sensors. The cushion only decelerates near the end and does not lock; the piston drifts on air loss, so use an external rod lock for holding.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X200-75S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.