Airtac MICJ Adjustable Mini Cylinder MICJ16X225-10
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X225-10 is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 225mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke225 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X225-10
Trim the forward stop by up to 10 mm on site without swapping cylinders thanks to the external screw, yielding a usable extend range of 215-225 mm. The AirTAC MICJ16X225-10 is a double-acting, round-body stainless-steel mini cylinder that pairs this on-site extend adjustment with a variable air cushion at both ends to soak up high-speed shock.
Built with a stainless barrel and rod for mild washdown resistance, it conforms to the ISO 6432 mounting interface for Ø16. Note this SKU lacks a magnet, so it cannot take CMSG/DMSG/EMSG sensors; the M5×0.8 port and M6x1.0 rod thread match the standard 16 mm bore format.
Airtac MICJ Adjustable Mini Cylinder MICJ16X225-10 Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X225-10 |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 225 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X225-10
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×225 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X225-10 Is Used
Flap Folding
Fold light packaging flaps precisely by trimming the forward position up to 10 mm on-site, using the stainless construction to resist humid washdown environments.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X225-10 the Right Cylinder?
If you need less push, the smaller 12 mm bore uses a bumper rather than an air cushion, so you must drop the cushion feature to step down. This adjustable-stop plus cushion combination shines when you need fast, repeatable set-position moves and want to dial out end-impact without adding external shock absorbers.
The stop screw sets the extend end position only; it is not a mid-stroke lock, and the piston will drift on air loss. For a held load, install an external rod lock or pilot check valve. Use LB foot, FA flange, or TC trunnion mounts (SDB pivot-block is not available on this adjustable variant). Because this SKU has no -S magnet, position sensing is not possible here.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X225-10 FAQ
This 16 mm bore double-acting cylinder pushes 100.5 N and pulls 86.4 N at 0.5 MPa. At 0.7 MPa it pushes 140.7 N and pulls 120.9 N. The theoretical max force is 20.5 kgf at 1.0 MPa, and it uses an M5×0.8 air port.
An external screw shortens the extend stroke by up to 10 mm (usable range 215-225 mm), while needle-set air cushions at both ends soak up high-speed shock. The cylinder does not hold position on air loss and drifts; for a held load use an external rod lock. This SKU has no magnet, so CMSG/DMSG/EMSG sensors cannot be fitted.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X225-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.