Airtac MICJ Adjustable Mini Cylinder MICJ16X25-10S
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X25-10S is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 25mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke25 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X25-10S
Dial in the forward stop on-site without swapping cylinders: this AirTAC MICJ16X25-10S round-body mini cylinder uses an external screw to shorten the extend stroke by up to 10 mm, giving a usable 15-25 mm forward range while retract remains full. A needle-set adjustable air cushion at both ends soaks up high-speed shock, letting you set the position and control the impact. The stainless-steel barrel and Ø6 mm piston rod resist mild corrosion and washdown, and the built-in magnet (-S) supports CMSG, DMSG and EMSG sensors.
Operating pressure spans 0.15-1.0 MPa at speeds of 30-800 mm/s.
Airtac MICJ Adjustable Mini Cylinder MICJ16X25-10S Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X25-10S |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 25 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X25-10S
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X25-10S Is Used
Micro-Clamp Positioning
Trim the extend stroke up to 10 mm to dial in the exact clamp contact on delicate machined parts, using the dual air cushions to prevent impact marking at high cycle rates.
Lab Sample Ejector
Ejects small vials or trays weighing under 5 kg safely; the stainless build handles wipe-downs, while the needle cushion decelerates the rod before the end of stroke.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X25-10S the Right Cylinder?
For lighter moves, the smaller MIJ series offers a bumper-only adjustable stroke but lacks the air cushion needed for high-speed deceleration; stepping up to the Ø20 MICJ raises the 0.5 MPa push force to 157 N. Choose this Ø16 bore when your payload sits near 5 kg and you need precise end-position tuning alongside shock absorption. The external stop screw sets the extend endpoint but does not lock the piston mid-stroke, so fit an external rod lock or pilot check valve if you must hold a load on air loss.
Mounting follows the standard ISO 6432 mini interface with LB foot, FA flange and TC trunnion options (SDB pivot block is not available on this adjustable variant). Because this SKU includes the -S magnet, you can directly mount CMSG, DMSG or EMSG reed and electronic switches for position sensing.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X25-10S FAQ
The theoretical maximum force is 20.5 kgf at 1.0 MPa.
An external screw shortens the extend stroke by up to 10 mm (usable 15-25 mm) without affecting the full retract, while the adjustable air cushions at both ends absorb high-speed shock. The cushion only decelerates near the stroke end and does not lock the piston; for load holding on air loss, use an external rod lock or pilot check valve. The -S suffix means it has a magnet for CMSG/DMSG/EMSG sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X25-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.