Airtac MICJ Adjustable Mini Cylinder MICJ16X25-20S
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X25-20S is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 25mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke25 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X25-20S
Trim the forward stop by up to 20 mm on-site without swapping hardware using this stainless-steel round-body mini cylinder. The MICJ16X25-20S is double-acting, featuring an external screw that shortens the extend stroke (usable range 5-25 mm) alongside a needle-adjustable air cushion at both ends to soak up high-speed shock.
The Ø16 mm bore conforms to the ISO 6432 mounting interface, fitting standard mini brackets, and includes an M5×0.8 port. The built-in magnet (-S) supports CMSG, DMSG, and EMSG sensors for position detection.
Airtac MICJ Adjustable Mini Cylinder MICJ16X25-20S Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X25-20S |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 25 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X25-20S
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| -20 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X25-20S Is Used
Light-Part Sorting
Dial in a 15 mm extend stop to push 5 kg product bins gently, relying on the air cushion to prevent slamming at 800 mm/s.
Film Feed Tensioning
Set a precise 20 mm forward stroke to tension packaging film, using the magnetic piston for exact position feedback.
Small Component Seating
Press lightweight plugs into housings with a safe 60 N working load while the adjustable cushion absorbs the impact.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X25-20S the Right Cylinder?
This Ø16 model shines in fast set-position moves where the adjustable extend stop and dual air cushions prevent end-of-stroke impact.
The stop screw sets the end position but is not a mid-stroke lock; the piston will drift on air loss, so add an external rod lock or pilot check valve to hold a suspended load. Mount via LB foot, FA flange, or TC trunnion (SDB pivot block is not available), and use the -S magnet for switch readiness.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X25-20S FAQ
The theoretical maximum force is 20.5 kgf at 1.0 MPa. This Ø16 bore uses an M5×0.8 port.
An external screw shortens the extend stroke by up to 20 mm (retract remains full), while a needle valve adjusts the air cushion at both ends to decelerate the piston near stroke end. The cushion is not a brake; the cylinder does not hold load on air loss. The -S suffix means it has a magnet for CMSG/DMSG/EMSG sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X25-20S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.