Airtac MICJ Adjustable Mini Cylinder MICJ16X250-100
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X250-100 is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 250mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke250 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X250-100
Trim the forward stop by up to 100 mm on site without swapping hardware using this AirTAC MICJ16X250-100 round-body mini cylinder. The external screw adjusts the extend end position only (yielding a usable 150-250 mm forward travel), while a needle-set variable air cushion at both ends soaks up high-speed shock. Retract travel remains the full 250 mm. Built as a double-acting stainless steel riveted unit, it resists mild corrosion and washdown environments.
It features an M5×0.8 air port, an M6x1.0 male rod thread, and conforms to the ISO 6432 mounting interface for standard mini brackets. Note this SKU lacks a magnet, so it cannot accept CMSG/DMSG/EMSG sensors.
Airtac MICJ Adjustable Mini Cylinder MICJ16X250-100 Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X250-100 |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 250 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X250-100
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×250 | Stroke length in mm. |
| -100 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X250-100 Is Used
Washdown Component Pusher
Push light machined parts into a washdown station using the stainless steel barrel and rod, trimming the forward stroke by up to 100 mm to accommodate different fixture widths.
Vertical Lift Gate
Lift a 5 kg access gate vertically at high speed, letting the adjustable air cushion decelerate the load smoothly at the extend end without slamming.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X250-100 the Right Cylinder?
The adjustable stop screw and dual cushions shine in fast set-position moves where you must dial in the exact forward endpoint and control impact without external shock absorbers.
Remember that the stop screw sets the end position but is not a mid-stroke lock; the piston will drift on air loss. Use an external rod lock or pilot check valve for held loads. Mount via LB foot, FA flange, or TC trunnion (SDB pivot-block is unavailable here), and select the -S variant if you need position sensing.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X250-100 FAQ
This 16 mm bore cylinder uses an M5×0.8 air port and an M6x1.0 male rod thread.
An external screw shortens the extend stroke by up to 100 mm on site, while a needle valve adjusts the air cushion at both ends to decelerate high-speed impacts. The cushion only slows the piston near the end of travel; it is not a brake. This SKU has no magnet and cannot take sensors, and the cylinder will drift on air loss unless you add an external rod lock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X250-100
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.