Airtac MICJ Adjustable Mini Cylinder MICJ16X250-10S
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X250-10S is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 250mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke250 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X250-10S
Dial in the exact forward stop on-site with the AirTAC MICJ16X250-10S, a stainless-steel round-body mini cylinder featuring an adjustable extend stroke and built-in magnet. An external screw trims the extend end position by up to 10 mm, letting you fine-tune the 240-250 mm forward travel without swapping hardware. The riveted stainless barrel and Ø6 mm rod shrug off mild washdown, and the M5×0.8 port feeds a double-acting system that pushes with 100.5 N at 0.5 MPa. A needle-set variable air cushion at both ends soaks up high-speed shock, while the -S magnet enables CMSG, DMSG or EMSG sensors for position tracking.
This ISO 6432 bore drops directly into standard mini brackets and clevises. The cushion only decelerates the piston near the stroke end; it is not a mid-stroke lock, so add an external rod lock or pilot check valve if you must hold a load on air loss.
Airtac MICJ Adjustable Mini Cylinder MICJ16X250-10S Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X250-10S |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 250 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X250-10S
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×250 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X250-10S Is Used
Package Diverting
Employs the -S magnet with DMSG sensors to confirm diverting arm position on the line, safely handling loads around 5 kg.
Film Roll Tensioning
Leverages the stainless construction for mild washdown resistance and the adjustable stop to set precise 240 mm forward tensioning limits.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X250-10S the Right Cylinder?
The MICJ16X250-10S shines in fast set-position moves where the 10 mm extend trim and adjustable air cushion prevent harsh impacts at the 30-800 mm/s operating speed range. Mount it via LB foot, FA flange or TC trunnion, but note the SDB pivot-block is not available on this adjustable variant. Because the -S magnet is present, you can directly mount reed or electronic switches.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X250-10S FAQ
Its theoretical maximum force is 20.5 kgf at 1.0 MPa.
An external screw shortens the extend stroke by up to 10 mm on-site, while retract remains full. A needle-set variable air cushion at both ends decelerates the piston at high speed but does not lock the position. The built-in -S magnet supports CMSG, DMSG and EMSG sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X250-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.