Airtac MICJ Adjustable Mini Cylinder MICJ16X250-30
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X250-30 is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 250mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke250 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X250-30
Dial in the forward stop on site with the AirTAC MICJ16X250-30, a stainless-steel round-body mini cylinder that pairs a 30 mm extend-stroke adjustment with needle-set air cushions at both ends. The external stop screw lets you trim the usable extend from 250 mm down to 220 mm without changing hardware, while the cushions absorb high-speed impact. Built to the ISO 6432 mounting interface, it drops into standard mini brackets and uses an M5×0.8 port with an M6x1.0 male rod thread.
The stainless barrel and rod shrug off mild washdown. Note this SKU lacks a magnet, so it cannot host CMSG/DMSG/EMSG sensors; the stop screw sets the end position but does not lock mid-stroke.
Airtac MICJ Adjustable Mini Cylinder MICJ16X250-30 Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X250-30 |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 250 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X250-30
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×250 | Stroke length in mm. |
| -30 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X250-30 Is Used
Light Divert Gate
Pushes a lightweight routing flap at speed, using the 30 mm extend trim to hit the exact deflection angle while the dual air cushions prevent end-cap slamming.
Film Roll Tensioner
Extends 250 mm to engage a packaging web; the adjustable forward stop dials in tension without swapping cylinders, handling a safe 60 N load.
Bin Lid Actuator
Lifts a 5 kg bin lid vertically; the needle cushion decelerates the 16 mm rod before the end of travel, and the stainless build resists humidity.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X250-30 the Right Cylinder?
Choose this 16 mm bore when you need a long 250 mm reach with fine 30 mm on-site extend tuning and high-speed cushioning. The external screw is strictly for setting the end position, not for holding load on air loss—add a pilot check valve if the payload must not drift.
Mount via LB foot, FA flange, or TC trunnion (SDB pivot-block is not offered on this adjustable variant). Because this exact SKU ships without a magnet, position sensing is impossible here; order an -S variant if you need CMSG/DMSG/EMSG switches.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X250-30 FAQ
This 16 mm bore double-acting cylinder uses an M5×0.8 port.
An external screw shortens the extend stroke by up to 30 mm (usable range 220-250 mm); retract remains full. Adjustable air cushions at both ends decelerate the piston at high speed but do not lock or hold the load—if air is lost, the piston drifts. This non-S SKU has no magnet for sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X250-30
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.