Airtac MICJ Adjustable Mini Cylinder MICJ16X30-10
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X30-10 is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 30mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke30 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X30-10
Trim the forward stop on site by up to 10 mm with the AirTAC MICJ16X30-10, a stainless-steel round-body mini cylinder built for ISO 6432 mounting interfaces. A needle-set adjustable air cushion at both ends soaks up high-speed shock, letting you dial in the exact extend position from 20 to 30 mm while controlling the impact. The external screw sets the end position but does not act as a mid-stroke lock.
The stainless barrel and rod resist mild corrosion and washdown environments. Because this SKU lacks the -S magnet, it cannot accept CMSG, DMSG, or EMSG sensors. It features an M5×0.8 port and a 6 mm piston rod with an M6x1.0 male thread.
Airtac MICJ Adjustable Mini Cylinder MICJ16X30-10 Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X30-10 |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 30 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X30-10
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X30-10 Is Used
Gauge Positioning
Dial in the 20-30 mm extend stop to trigger a gauge precisely, using the dual air cushions to prevent bounce at 800 mm/s.
Lab Dispenser
Push a small fluid dispenser nozzle against a stop, relying on the stainless build for mild washdown resistance.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X30-10 the Right Cylinder?
When sizing this 16 mm bore, stepping down means moving to an 8/10/12 mm MIJ bumper-only model, which lacks the adjustable air cushion and yields significantly less force. Stepping up to the Ø20 MICJ increases your 0.5 MPa push force to 157 N if the 100.5 N here is insufficient. The adjustable stop screw and dual cushions shine in fast set-position moves where you must repeatedly hit a precise spot without slamming.
Remember that this cylinder does not hold position on air loss; the piston drifts, so add an external rod lock or pilot check valve for suspended loads. For mounting, use LB foot, FA flange, or TC trunnion brackets (SDB pivot-block is not available on this adjustable variant). If you need position sensing, select the -S magnet version to enable sensor switches.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X30-10 FAQ
This double-acting cylinder pushes 100.5 N and pulls 86.4 N at 0.5 MPa. At 0.7 MPa, it pushes 140.7 N and pulls 120.9 N, with a theoretical max of 20.5 kgf at 1.0 MPa. The air port is M5×0.8.
An external screw shortens the extend stroke by up to 10 mm, while needle valves adjust the air cushions at both ends to absorb high-speed shock. The stop screw is not a mid-stroke lock, and the cylinder will drift on air loss, so use an external rod lock for holding. This non-S SKU cannot take sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X30-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.