Airtac MICJ Adjustable Mini Cylinder MICJ16X300-10
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X300-10 is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 300mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke300 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X300-10
Trim the forward stop by up to 10 mm on site without swapping hardware using this stainless steel round-body mini cylinder. The MICJ16X300-10 is a double-acting actuator featuring a variable air cushion at both ends to soak up high-speed shock, while the external screw shortens the extend stroke to a usable 290-300 mm range. Retract remains full length. Built with an M5×0.8 port and an M6x1.0 male rod thread, it drops directly into standard ISO 6432 mini-cylinder mounting brackets and clevises.
The stainless barrel and piston rod resist mild corrosion and washdown environments. Note this specific SKU lacks a magnet and cannot host CMSG, DMSG, or EMSG sensors; order the -S variant if position detection is required.
Airtac MICJ Adjustable Mini Cylinder MICJ16X300-10 Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X300-10 |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 300 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X300-10
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×300 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X300-10 Is Used
Precision Stop Trimming
Dial in the exact 290-300 mm extend endpoint on a 60 N workpiece feeder to avoid mechanical hard stops, using the 10 mm adjuster and air cushion to remove end-of-stroke shock.
Light Part Ejection
Push small plastic parts off a belt at high speed; the stainless construction handles mild washdown, while the cushion prevents the 5.1 kg load from slamming the cylinder body.
Adjustable Forming Stop
Set a precise forward position for a light pressing task, adjusting the stroke on the fly as material thickness varies without re-engineering the fixture.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X300-10 the Right Cylinder?
When sizing, step up to the Ø20 bore if you need more push (157 N @0.5 MPa), or drop to the MIJ bumper-only series for lighter tasks, as there is no cushioned MICJ bore below 16 mm. The adjustable extend stop plus dual air cushions shine in fast set-position moves where you must dial in a precise forward endpoint and control impact without adding external shock absorbers. Mount via LB foot, FA flange, or TC trunnion (SDB pivot-block is not available on this adjustable variant). Remember the stop screw sets the end position but is not a mid-stroke lock; the cylinder will drift on air loss, so add an external rod lock or pilot check valve for held loads.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X300-10 FAQ
This 16 mm bore cylinder uses an M5×0.8 port.
An external screw shortens the extend stroke by up to 10 mm (retract is unaffected), while a needle-set air cushion at both ends decelerates the piston near stroke ends to absorb high-speed shock. The cushion only decelerates and is not a brake; the cylinder cannot hold a load on air loss and will drift, so use an external rod lock for holding. This SKU has no magnet and cannot take sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X300-10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.