Airtac MICJ Adjustable Mini Cylinder MICJ16X300-10S
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X300-10S is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 300mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke300 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X300-10S
Dial in a precise forward stop on-site with the AirTAC MICJ16X300-10S, a stainless-steel round-body mini cylinder featuring an external screw that shortens the extend stroke by up to 10 mm. The built-in magnet enables position sensing, while needle-set air cushions at both ends soak up high-speed shock. This double-acting actuator conforms to the ISO 6432 mounting interface for straightforward bracket integration.
The stainless barrel and piston rod resist mild corrosion and washdown environments, making it a robust choice for demanding automated tooling.
Airtac MICJ Adjustable Mini Cylinder MICJ16X300-10S Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X300-10S |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 300 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X300-10S
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×300 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X300-10S Is Used
Diverter Gate Positioning
Tunes the exact extend stop for a sorting flap, using the 10 mm adjustment to dial in the angle while the air cushion absorbs the impact of high-speed actuation.
Light Part Ejector
Pushes small components off a belt with a safe 60 N working load, relying on the stainless construction for mild washdown resistance during cleaning.
Sensor Probe Deployment
Extends a testing probe 300 mm into a fixture, using the built-in magnet with a DMSG sensor to confirm the extended position before initiating the test cycle.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X300-10S the Right Cylinder?
When sizing this 100.5 N (at 0.5 MPa) actuator, note that dropping down requires moving to an MIJ bumper-only variant, as standard cushioned models start at this 16 mm bore. The adjustable stop and dual air cushions shine in fast set-position moves where you must tune the forward end point and decelerate the load without swapping physical components.
Remember that the stop screw sets the end position but does not act as a mid-stroke lock; the piston will drift on air loss, so add an external rod lock or pilot check valve for holding suspended loads. For mounting, use LB foot, FA flange, or TC trunnion brackets (the SDB pivot block is not available on this adjustable variant). Because this SKU includes the -S magnet, you can directly mount CMSG, DMSG, or EMSG sensors for switching.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X300-10S FAQ
This 16 mm bore cylinder uses an M5×0.8 port and a 6 mm rod.
An external screw shortens the extend stroke by up to 10 mm on-site, giving a usable forward range of 290-300 mm; retract remains full. Needle valves adjust the air cushions at both ends to decelerate the piston near stroke end. The -S suffix means it has a built-in magnet for CMSG, DMSG, or EMSG sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X300-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.