Airtac MICJ Adjustable Mini Cylinder MICJ16X300-75
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X300-75 is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 300mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke300 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X300-75
Trim the forward stop by up to 75 mm on site without swapping hardware using the AirTAC MICJ16X300-75. This 16 mm bore, double-acting stainless round-body mini cylinder pairs that adjustable extend stroke with a needle-set variable air cushion at both ends to soak up high-speed shock. You get a 300 mm nominal extend (usable range 225-300 mm) and a full retract.
Built with a stainless-steel barrel and rod for mild washdown resistance, it uses the ISO 6432 mounting interface. Note this SKU lacks a magnet, so it cannot take CMSG/DMSG/EMSG sensors; the M5×0.8 port and M6x1.0 rod thread match standard mini fittings.
Airtac MICJ Adjustable Mini Cylinder MICJ16X300-75 Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X300-75 |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 300 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X300-75
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×300 | Stroke length in mm. |
| -75 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X300-75 Is Used
Soft Transfer Diverter
Use the needle-set air cushions to decelerate the 300 mm stroke at high speed when kicking light cartons, preventing impact damage without adding external shocks.
Lab Dispense Head
Set a precise forward position for a 5 kg liquid dispense head on a stainless frame, dialing the stop back 20 mm for different container heights.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X300-75 the Right Cylinder?
If you need less force, there is no smaller cushioned bore in this family, so you would drop to the MIJ bumper-only series. This 16 mm bore shines in fast set-position moves where the 75 mm extend trim and dual cushions prevent end-of-stroke banging.
Remember the stop screw sets the end position but is not a mid-stroke lock, and the cylinder drifts on air loss. For a held load, add an external rod lock or pilot check valve. Mount via LB foot, FA flange, or TC trunnion (SDB pivot-block is not available), and choose the -S variant if you need position sensing.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X300-75 FAQ
This 16 mm bore cylinder pushes 100.5 N and pulls 86.4 N at 0.5 MPa. At 0.7 MPa it pushes 140.7 N and pulls 120.9 N. The theoretical max force is 20.5 kgf at 1.0 MPa, and it uses an M5×0.8 air port with an M6x1.0 male rod thread.
An external screw shortens the extend stroke by up to 75 mm (usable 225-300 mm) while retract remains full; the needle-set air cushions only decelerate near the ends to absorb high-speed shock. This SKU has no -S magnet so it cannot take sensors, and it will drift on air loss since the screw is not a mid-stroke lock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X300-75
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.