Airtac MICJ Adjustable Mini Cylinder MICJ16X50-20
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X50-20 is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 50mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke50 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X50-20
The MICJ16X50-20 is a round-body stainless mini cylinder that lets you dial in the forward stop on site. An external screw shortens the extend end by up to 20 mm, so you can set the position without swapping cylinders. At the same time, a needle-adjustable air cushion at both ends absorbs shock at high speed, protecting the load and the machine.
The stainless barrel and rod resist mild corrosion and washdown, and the ISO 6432 mounting interface fits standard mini brackets. Port is M5×0.8. This SKU has no magnet, so it cannot accept a magnetic switch; choose the -S variant for CMSG/DMSG/EMSG sensors.
Airtac MICJ Adjustable Mini Cylinder MICJ16X50-20 Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X50-20 |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 50 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X50-20
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| -20 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X50-20 Is Used
Set-Position Clamping
Use the 20 mm adjustable stroke to fine-tune the clamp forward position on a fixture, while the cushion prevents shock at the end of each cycle.
Light Assembly Stop
Position a 100 N stop for small part alignment in assembly lines, adjusting the extend limit on the fly without changing the cylinder.
High-Speed Indexing
Run at up to 800 mm/s in light indexing tasks; the adjustable cushion at both ends absorbs the kinetic energy and extends component life.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X50-20 the Right Cylinder?
The adjustable stop plus cushion suits fast set-position moves where you want to control both the endpoint and the impact. Remember this cylinder does not hold position on air loss - use an external rod lock or pilot check valve for holding. Mounting options include LB foot, FA flange, and TC trunnion; SDB pivot-block is not available on this variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X50-20 FAQ
At 0.5 MPa, push is 100.5 N and pull is 86.4 N. At 0.7 MPa, push is 140.7 N and pull is 120.9 N. Theoretical maximum force is 20.5 kgf at 1.0 MPa.
An external screw shortens the extend end by up to 20 mm, so the usable extend stroke is 30-50 mm; retract remains full. The air cushion at both ends decelerates the piston near stroke end but is not a lock. This SKU has no magnet, so it cannot take a sensor; the -S version adds one for CMSG/DMSG/EMSG.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X50-20
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.