Airtac MICJ Adjustable Mini Cylinder MICJ16X50-30S
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X50-30S is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 50mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke50 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X50-30S
Trim the forward stop by up to 30 mm on site without swapping hardware using this AirTAC MICJ16X50-30S double-acting mini cylinder. The external screw shortens the extend end position (usable range 20-50 mm), while a needle-set adjustable air cushion at both ends soaks up high-speed shock so you control both the landing position and the impact force.
The stainless-steel round barrel and Ø6 mm piston rod resist mild corrosion and washdown, dropping directly into standard ISO 6432 mini-cylinder brackets. A built-in magnet (-S) supports CMSG, DMSG and EMSG sensors for end-of-stroke confirmation.
Airtac MICJ Adjustable Mini Cylinder MICJ16X50-30S Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X50-30S |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 50 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X50-30S
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| -30 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X50-30S Is Used
Flap Deflection
Tucks carton flaps at high cycle rates; the dual adjustable air cushions absorb the repeated end-of-stroke shock to protect the 5 kg payload.
Lab Dispense Stop
Acts as an adjustable physical stop for a fluid nozzle, dialing the extend stroke down 30 mm to vary fill depth while the -S magnet confirms retraction.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X50-30S the Right Cylinder?
Choose this MICJ model when you need precise set-position moves at speed, as the extend stop screw and dual cushions let you dial in the exact forward landing without end-of-stroke slamming.
The stop screw sets the end position but is not a mid-stroke lock; the piston will drift on air loss, so fit an external rod lock or pilot check valve to hold a suspended load. For mounting, use LB foot, FA flange or TC trunnion (the SDB pivot block is not offered on this adjustable variant), and rely on the internal magnet for position sensing.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X50-30S FAQ
The theoretical maximum force is 20.5 kgf at 1.0 MPa, and the air port size is M5×0.8.
An external screw shortens the extend stroke by up to 30 mm (retract remains full), while needle valves adjust the air cushions at both ends to decelerate the piston near the ends. The cushion only decelerates and is not a brake; the cylinder does not hold position on air loss. The -S magnet enables CMSG, DMSG and EMSG sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X50-30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.