Airtac MICJ Adjustable Mini Cylinder MICJ16X60-50S
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X60-50S is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 60mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke60 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X60-50S
Dial in the forward stop on site without swapping hardware: the MICJ16X60-50S uses an external screw to trim the extend end position by up to 50 mm, giving a usable 10-60 mm forward travel while retract remains full. Built as a double-acting, round-body stainless-steel mini cylinder, it pairs that settable stop with a needle-adjustable air cushion at both ends to soak up high-speed shock.
The stainless barrel and rod resist mild washdown corrosion, the body conforms to ISO 6432 mini mounting dimensions, and the built-in -S magnet supports CMSG, DMSG and EMSG sensors.
Airtac MICJ Adjustable Mini Cylinder MICJ16X60-50S Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X60-50S |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 60 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X60-50S
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -50 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X60-50S Is Used
Carton Flap Folding
Set a precise forward position to fold light cardboard flaps without crushing the box, using the adjustable stroke to dial in the exact 40 mm reach required on site.
Lab Sample Routing
Leverage the stainless build and 5.1 kg vertical lift capacity to index fluid trays in washdown test cells, tracking position with a DMSG sensor on the -S magnet.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X60-50S the Right Cylinder?
Size this bore against its neighbors: stepping up to the Ø20 bore raises 0.5 MPa push to 157 N, while dropping below Ø16 moves you to the MIJ bumper-only series, which lacks the adjustable air cushion. Choose this Ø16 when you need precise set-position moves at speed, as the combination of the extend stop screw and dual-end cushion lets you tune both the landing spot and the impact deceleration. The cylinder drifts on air loss—the stop screw sets the end position but is not a mid-stroke lock, so add an external rod lock or pilot check valve for held loads. Mount via LB foot, FA flange or TC trunnion (SDB is not offered on this adjustable variant), and use the -S magnet for position sensing.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X60-50S FAQ
The theoretical maximum force is 20.5 kgf at 1.0 MPa.
An external screw shortens the extend stroke by up to 50 mm (usable 10-60 mm), while the needle-adjustable air cushion at both ends absorbs high-speed shock. The cylinder does not hold position on air loss—the piston drifts, so use an external rod lock for holding. The -S magnet enables CMSG, DMSG and EMSG sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X60-50S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.