Airtac MICJ Adjustable Mini Cylinder MICJ16X60-75
The AirTAC MICJ Adjustable Mini Cylinder MICJ16X60-75 is a genuine double acting, double rod, adjustable stroke + cushion round-body mini air cylinder with a Ø16mm bore and 60mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface fits standard ISO 6432 mini-cylinder mounting interfaces.
- BoreØ16 mm
- Stroke60 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MICJ Adjustable Mini Cylinder MICJ16X60-75
Trim the forward stop by up to 75 mm on site with the AirTAC MICJ16X60-75, a double-acting stainless-steel round-body mini cylinder. A needle-set variable air cushion at both ends soaks up high-speed shock, letting you set the exact extend position and control the impact without swapping parts.
Built to the ISO 6432 mounting interface, this Ø16 bore drops into standard mini brackets and clevises. The stainless barrel and piston rod resist mild corrosion and washdown environments. Note that this specific SKU lacks a magnet and cannot host CMSG, DMSG, or EMSG sensors.
Airtac MICJ Adjustable Mini Cylinder MICJ16X60-75 Technical Specifications
| Model | Airtac MICJ Adjustable Mini Cylinder MICJ16X60-75 |
|---|---|
| Series | MICJ ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 60 mm |
| Acting type | Double acting, double rod, adjustable stroke + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 86 N |
| 0.7 MPa | 121 N |
| Max (@1.0 MPa) | 18 kgf |
MIJ / MICJ are double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac MICJ Adjustable Mini Cylinder MICJ16X60-75
| MICJ | ISO 6432 round-body mini cylinder (adjustable-stroke, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -75 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (double rod, adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MICJ Adjustable Mini Cylinder MICJ16X60-75 Is Used
Washdown Component Pusher
Push small parts on a food-grade line where the stainless barrel resists mild corrosion, using the adjustable forward stop to tune the ejection distance without changing hardware.
Light-Load Diverter Gate
Actuate a lightweight routing gate at high speed, setting the extend end precisely and letting the dual needle cushions soak up the shock to prevent gate bounce.
Is the Airtac MICJ Adjustable Mini Cylinder MICJ16X60-75 the Right Cylinder?
For lighter duties, the MIJ bumper-only series is the next step down, as the cushioned MICJ line starts at this Ø16 bore. If your application requires more force, stepping up to the Ø20 bore raises the 0.5 MPa push force to 157 N. The external stop screw and dual air cushions are ideal for fast, repeatable set-position moves that need end-deceleration. Remember that the stop screw only trims the extend end and is not a mid-stroke lock; the piston will drift on air loss, so fit an external rod lock or pilot check valve to hold a load. Mount via LB foot, FA flange, or TC trunnion (SDB pivot-block is not available), and select a -S variant if you need position sensing.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MICJ Adjustable Mini Cylinder MICJ16X60-75 FAQ
This Ø16 bore double-acting cylinder features an M5×0.8 port and an M6x1.0 male rod thread.
An external screw shortens the extend stroke by up to 75 mm on site, while a needle-set variable air cushion at both ends decelerates the piston near the ends to absorb high-speed shock. The cushion only decelerates and is not a brake; the piston drifts on air loss, so use an external rod lock for holding. This SKU has no magnet and cannot take sensors; choose a -S variant for CMSG/DMSG/EMSG switches.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC MICJ Cylinders
Request a Quote for Airtac MICJ Adjustable Mini Cylinder MICJ16X60-75
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.